SMC Networks ZK2 A Series Скачать руководство пользователя

Страница: 75 / 80

-74-

No. ZK2-OM01301

12. Limitations of Use

■

Exhaust from Ejector

The exhaust resistance should be as small as possible to obtain the full ejector performance. There should

be no shield around the exhaust slit for silencer exhaust type. When the product is installed, one of the ports

should be open to atmosphere.

For port exhaust type, back pressure may increase depending on the piping size and length. Ensure that the

back pressure does not exceed 0.005 MPa (5 kPa).

For the nozzle products with a nozzle diameter for a large

amount of exhaust air (air consu suction flow), such as ø1.5(ZK[ ] 15), precaution should be taken on

vacuum pressure decrease. Figure A below shows the relation between the exhaust piping (piping diameter

and length) and vacuum pressure When connecting pipes on port exhaust types with an outer diameter of Ø8

or more, connect them so that the joints do not interfere with each other (Fig. B).

Exhaust slit
(On both sides)

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

1000

2000

3000

4000

5000

6000

真空圧力［

］

配管長さ［

］

［測定条件】
・供給圧

0.4MPa

・真空ポート全閉
・排気側配管の先端は開放

注）実測値であり保証
値ではありませんので
ご了承願います。

TU0805

T0806

TU1065

T1075

Note) The values are
measured values. Not
guaranteed values.

[Measuring conditions]
- Supply pressure 0.4 MPa
- Vacuum port is fully closed

Piping length [mm]

Fig. A

. Vacuum pressure f

or piping (ZK2□15)

[

]

Fig. B Example of piping

Nipple

（

KQ2N08-99

）

Tube

（

TU0805 or T0806

）

Straight type of
different diameter

（

KQ2H08-10A

）

Tube

（

TU1065 or T1075

）

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды