SMC Networks ZK2 A Series Скачать руководство пользователя

Страница: 73 / 80

-72-

No. ZK2-OM01301

11.2. Vacuum Pump System Flow Rate Characteristics

The graph shows the suction flow rate characteristics of the vacuum pump system at different vacuum

pressure.

■

ZK2P00

The actual suction flow at the point of suction varies depending on the piping conditions to the vacuum port.

(The above graph shows the value when V port is ø8.)

11.3. Vacuum Release Flow Rate Characteristics

The graph shows the flow rate characteristics at different supply pressures when the vacuum break flow

adjusting needle is open from the fully closed state.

■

ZK2

□□□ (Ejector)

The actual suction flow at the point of suction varies depending on the piping conditions to the vacuum port.

(The above graph shows the value of the ZK2B07)

Port size

Flow rate characteristics of V to PV (Vacuum side)

PV port

V port

C[dm

/(s·bar)]

ø6

ø8

0.39

0.14

0.09

Flow rate characteristics of different vacuum pressure

Содержание ZK2 A Series

















































































Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды

SMC Networks ZK2 A Series, Руководство по эксплуатации

Результаты поиска

Содержание ZK2 A Series

Отзывы:

Похожие инструкции для ZK2 A Series

Бренды по названию

Популярные бренды