SMC Networks RS2H Series Скачать руководство пользователя страница 23

Страница: 23 / 25

- 22 -

Detail of trouble

Cause

Countermeasure

Cylinder starts
operating at high
speed after being
stopped for a long
time.

1. Variations in cylinder

residual pressure
between continuous
operation and restarted
operation after being
stopped for a long time.

・

Consider using a valve to prevent cylinder lurching.

Switch does not turn
on. (Switch does not
turn on occasionally.)

1. Power failure or

defective connection

・

Repair power source and rewire it properly.

2. Switch out of position

・

Slide switch on cylinder to see where it turns on, and reset in the

correct position.

3. Reduction in magnetic

force

・

If there is a source of magnetic force nearby, place cylinder away

from it or shield it.

・

If cylinder is getting hot, modify operating conditions such as

frequency to keep the temperature below 60

・

Replace cylinder if switch still does not turn on with the measures

above.

4. Reduction in switch

sensitivity

・

Solve problems of ambient temperature, vibration and impact.

Replace switch if they cannot be solved.

Switch does not turn
off. (Switch does not
turn off occasionally.)

1. Welded reed switch

contacts

・

Check voltage and load are lower than rated values, and replace
switch.

2. Continuous ON state due

to external magnetic
force

・

If there is a source of magnetic force nearby, place cylinder away

from it or shield it.

・

If cylinder is getting hot, modify operating conditions such as

frequency to keep the temperature below 60

℃

・

Replace cylinder if switch still does not turn on with the measures

above.

Содержание RS2H Series


























Результаты поиска

Содержание RS2H Series

Отзывы:

Похожие инструкции для RS2H Series

Бренды по названию

Популярные бренды

SMC Networks RS2H Series, Руководство по эксплуатации

Результаты поиска

Содержание RS2H Series

Отзывы:

Похожие инструкции для RS2H Series

Бренды по названию

Популярные бренды