SMC Networks EX260-SEN2-X205 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 48

background image

-12-

No.EX

※※

-OMX1001

■

Wiring

Select the appropriate cables to mate with the connectors mounted on the SI unit.

○Fieldbus interface connector layout

BUS OUT: RJ45 8-pin socket

No.

Designation

Description

1

Tx+

Transmit Data +

2

Tx-

Transmit Data -

3

Rx+

Receive Data +

4

-

-

5

-

-

6

Rx-

Receive Data -

7

-

-

8

-

-

BUS IN: RJ45 8-pin socket

No.

Designation

Description

1

Tx+

Transmit Data +

2

Tx-

Transmit Data -

3

Rx+

Receive Data +

4

-

-

5

-

-

6

Rx-

Receive Data -

7

-

-

8

-

-

Connect the "BUS IN" connector to the upstream device (PLC etc.) and connect the "BUS OUT" connector
to the downstream device.

•Use only plugs conforming to FCC standards.
•Shielded Ethernet cable is recommended.

NOTE

•Be sure to fit a seal cap on any unused connectors.

The seal cap prevents foreign matter from entering into the product.

«
...
11
12
13
14
15
...
»

Содержание EX260-SEN2-X205

















































Отзывы:

Нет отзывов

Похожие инструкции для EX260-SEN2-X205

Бренд: S&C Страницы: 40

Бренд: K&K Страницы: 6

Бренд: Valcom Страницы: 6

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

Бренд: Tylo Страницы: 51

Бренд: K&K Страницы: 10

Бренд: mikroElektronika Страницы: 3

Бренд: Window Master Страницы: 7

Бренд: IDEATEC Страницы: 32

Бренд: Broadcast Tools Страницы: 15

Бренд: Hach Страницы: 504

Бренд: Rain Bird Страницы: 48

Бренд: Sullair Страницы: 31

Бренд: Belimo Страницы: 9

Бренд: Zencontrol Страницы: 2

Бренд: Daikin Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды