C
HAPTER
23
| ACL Commands
– 323 –
ARP/RARP opcode set to ARP,
rarp
- frame must have ARP/
RARP opcode set to RARP,
other
- frame has unknown ARP/
RARP opcode flag; Default:
any
)
arp-flags
- One of the following ARP flags:
request
- Frame must have ARP Request or RARP Request
opcode flag set.
smac
- ARP frame where sender hardware address (SHA)
field is equal to the SMAC address.
tmac
- RARP frames where target hardware address (THA)
is equal to the SMAC address.
len
- ARP/RARP frames where the hardware address length
(HLN) is equal to Ethernet (0x06) and the protocol address
length (PLN) is equal to IPv4 (0x04).
ip
- ARP/RARP frames where the hardware address space
(HRD) is equal to Ethernet (1).
ether
[
0
|
1
|
any
] - Frames can be matched according to
their ARP/RARP protocol address space (PRO) settings
(Options:
0
- ARP/RARP frames where the PRO is equal to IP
(0x800) must not match this entry,
1
- ARP/RARP frames
where the PRO is equal to IP (0x800),
any
- any value is
allowed; Default:
any
)
ip
- One of the following IP parameters:
sip
- Source IP address (a.b.c.d/n) or
any
.
dip
- Destination IP address (a.b.c.d/n) or
any
.
protocol
- IP protocol number (0-255) or
any
.
ip-flags
- One of the following IP flags:
ttl
- Time-to-Live flag with any value.
options
- Options flag with any value.
fragment
[
0
|
1
|
any
] - Specifies the fragment offset
settings for this rule. This involves the settings for the More
Fragments (MF) bit and the Fragment Offset (FRAG OFFSET)
field for an IPv4 frame. (Options:
0
- IPv4 frames where the
MF bit is set or the FRAG OFFSET field is greater than zero
must not match this entry,
1
- IPv4 frames where the MF bit
is set or the FRAG OFFSET field is greater than zero must
match this entry,
any
- any value is allowed; Default:
any
)
icmp
- One of the following ICMP parameters:
sip
- Source IP address (a.b.c.d/n) or
any
.
dip
- Destination IP address (a.b.c.d/n) or
any
.
icmp-type
- ICMP type number (0-255) or
any
.
icmp-code
- ICMP code number (0-255) or
any
.
ip-flags
- One of the IP flags listed under the
ip
parameter.
Содержание 8028L2
