background image

 

 

ASSEMBLE FRONT PANEL

 

10

 

SELECT:

 

 

3 x 1.980 Wall Sheets

 

1 x 3.020 Top Plate (Red)

 

1 x 3.020 Bottom Plate (Green)

 

2 x 1.980 Door Jamb Flashings

 

40 x 30mm Galv Clouts

 

28 x Rivets

 

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER 

BASE PLATE –READ THE FOLLOWING;

 

 

For sheds with Raised Base Plate option only (see page 6), deduct 

30mm from measurement shown between Top and Bottom Plates on 
all wall panels, so cladding protrudes 20mm below bottom plate

.

 

STEP 1:

 

 

• 

Lay out 1 x Top Plate and 1 x Bottom Plate on a flat surface 
as shown. 

 

STEP 3:

 

 

• 

Place 3x Wall Sheets on timber, ensuring wall sheets fit under-
neath door jamb flashings. 

 

 

• 

Ensure that the top of the sheet is flush with the top of the Top 
Plate and that the sides of the wall sheets overhang the Top 
Plate by 

15mm

 as shown. Nail wall sheets to Top Plate (two 

clouts per pan)

 

 

• 

Nail the wall sheets to the Bottom Plate making sure that the 
Plates are the correct distance apart and that the sides of the 
wall sheet overhang the Bottom Plate by 

15mm

.

 

 

• 

Drill & rivet Door Jamb Flashings to wall sheets using four riv-

Plan View

 

STEP 2:

 

 

• 

Using 2 x 30mm clouts, nail the Door Jamb Flashing flush 
with the top of the Top Plate at the correct  measurement as 
shown in plan view. Pre drill holes using a 3.5mm drill bit

 

 

• 

Check the distance between the top and bottom plates then 
use a further 2 x 30mm clouts to nail the Door Jamb Flashings 
to the bottom Plate. Pre drill holes.

 

STEP 4:

 

 

• 

Place the door on the panel (In open position, approx 20mm 
below top of top plate). Using two rivets, rivet the top and bot-
tom hinges to the Door Jamb Flashing, ensuring door closes 
properly. 

 

 

• 

Fit remaining rivets.

 

NOTE: 

Door can be hinged on either side.

 

BOTTOM PLATE

 

1948mm

 

TOP PLATE

 

1948mm

 

530mm

 

1460mm

 

TOP PLATE

 

DOOR OPENING

 

TOP PLATE

 

TOP PLATE

 

15mm

 

15mm

 

x3

 

x3

 

TOP

 

PLATE

 

DOOR

 

JAMB

 

NAIL

 

15mm

 

15mm

 

x3

 

x3

 

x3

 

x3

 

NOTE: 

The

 

Doorway is standard at 530mm from left

-

hand end. 

To shift the doorway to the right

-

hand side of the front 

wall, simply measure 530mm from the right

-

hand end.

 

Содержание SM3015

















Отзывы: