Smartgen HEM4000 Скачать руководство пользователя страница 41

Страница: 41 / 46

HEM4000 Engine Controller User Manual Page 41 of 46

COMMISSIONING

Before formal operation, following examinations are suggested:

Ensure all the connections are correct and wire diameter is suitable.

Ensure the DC power of the controller is equipped with fuse and that it is correctly connected with the

passive and negative anodes of the starter battery.

Take proper measures to stop engine to crank successfully (e. g.: remove the connection wire of the

fuel valve.). Make sure everything is correct and power on the starter battery, then the controller shall

conduct program.

Press “Start” button, and the engine shall start. After the starting times set, the controller shall give out

starting failure signal. Press “Stop” button and the controller shall recover.

Recover the actions that stop the engine to start successfully (recover the connection wire of the fuel

valve.), and press the “Start” button again and the engine shall start. If everything is Ok, the engine

shall work from idle speed running (if there is idle speed set) to normal running. During this period,

please observe the working situation of the engin

If there is any other question, please contact SmartGen’s service personnel.

Содержание HEM4000















































Результаты поиска

Содержание HEM4000

Отзывы:

Похожие инструкции для HEM4000

Бренды по названию

Популярные бренды

Smartgen HEM4000, Руководство пользователя

Результаты поиска

Содержание HEM4000

Отзывы:

Похожие инструкции для HEM4000

Бренды по названию

Популярные бренды