background image

                                       

 

HEM4000 Engine Controller User Manual                                                                                      Page 37 of 46 

8.5

 

CONDITION SELECTION OF CRANK DISCONNECTION 

Table 12 – Crank Disconnection Conditions 

No.   

Setting description 

Engine Speed 

Oil pressure 

Oil pr Engine Speed 

NOTE:

 

─ 

There are 3 kinds of conditions that can disconnect the starter and the engine. Speed sensor and oil pressure sensor 

can be used independently. It is suggested that oil pressure sensor matches speed sensor together aiming to separate 

starting motor from the engine as soon as possible and judge whether it is started successfully precisely. 

─ 

Speed sensor is the magnetic equipment which is installed in the engine for detecting flywheel teeth number. 

─ 

If speed sensor is selected, please make sure that the flywheel teeth number is the same as the settings, or over speed 

shutdown and under speed shutdown may happen. 

─ 

If there is not speed sensor in the unit, please do not select corresponding items, or start failure and loss of speed signal 

alarm and shutdown may happen. 

─ 

If there is not oil pressure sensor in the unit, please do not select corresponding items. 

8.6

 

MAINTENANCE SETTING 

Table 13 – Maintenance Setting 

Item 

Content 

Description 

Enable Choice 

0: Disabled, 1: Enabled 

Applicable  to  set  whether  maintenance 
function is active or not. 

Maintenance Time 

(0-30000)h 

Hours  from  maintenance  enable  to 
maintenance start. 

Maintenance Time Due 
Action 

0: No Action; 
1: Warning; 
2: Shutdown; 
3: Indication. 

Alarm  action  when  remaining  maintenance 
time is 0. 

Pre-alarm A Time 

(0-30000)h 

Remaining maintenance time. 

Pre-alarm A Action 

Same as the Maintenance 
Time Due Action 

Action  when  remaining  maintenance  time 
reaches pre-alarm A time. 

Pre-alarm B Time 

(0-30000)h 

Remaining maintenance time. 

Pre-alarm B Action 

Same as the Maintenance 
Time Due Action 

Action  when  remaining  maintenance  time 
reaches pre-alarm B time. 

Maintenance Timing 
Way 

0: Unit Running Time 
1: Real Time Clock 

The timing way of maintenance. 

Reset Maintenance Time   

Applicable  to  reset  maintenance  time  after 
maintenance is finished. 

Maintenance Description   

Applicable to put in maintenance name, e.g. 
change engine oil. 

Содержание HEM4000















































Отзывы: