background image

                                         

 

HAT600P Series ATS Controller User Manual                                                                              Page 35 of 58

 

9.5

 

DEFINED COMBINATION OUTPUT 

Defined combination output is composed by 3 parts: OR condition output SW1/SW2 and AND condition 
output SW3.   

 

SW1 or SW2 is 

TRUE

, and SW3 is 

TRUE

, defined combination output is outputting; 

SW1 and SW2 are 

FALSE

, or SW3 is 

FALSE

, defined combination output is not outputting. 

NOTE 1:

 SW1, SW2, SW3 can be set as any contents except for “defined combination output” in the 

output settings. 

NOTE  2:

  3  parts  of  defined  combination  output  (SW1,  SW2,  SW3)  couldn’t  include  or  recursively 

include themselves. 

For example:   

Contents of OR condition output SW1: Input port 1 is active; 
Close when OR condition output SW1 is active /inactive: close when active (disconnect when inactive); 
Contents of OR condition output SW2, input port 2 is active; 
Close when OR condition output SW2 is active /inactive: close when active (disconnect when inactive); 
Contents of AND condition output SW3: Input port 3 is active; 
Close  when  AND  condition  output  SW3  is  active  /inactive:  close  when  active  (disconnect  when 
inactive);   
Output result is as below:   
When input port 1 active or input port 2 is active, if input port 3 is active, defined combination output is 
outputting; If input port 3 is inactive, defined combination output is not outputting; 
When input port 1 is inactive and input port 2 is inactive, whatever input port 3 is active or not, defined 
combination output is not outputting.   

9.6

 

Over Current Definite Time and Inverse Definite Time Settings 

Definite Time

: Over current delay is fixed delay; different over current values correspond to the same 

delay, which is the pre-set delay time;   

Inverse  Definite  Time

: Over  current  delay decreases  as  over  current  increases; different  over  current 

values correspond to different delays;   
Inverse over current delay formula is as below:   

 

      T: Over current delay value (s) 
      t: Timing multiplier 
      IA: Current maximum current (L1/L2/L3) 
      IT: Pre-set value of over current 
       
      Input conditions: T= 36, IA= 550A, IT= 500A 
      Output result: T= 3600s(1h) 

Содержание HAT600P Series



























































Отзывы: