SMAR LD291 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 84

SMAR LD291 Скачать руководство пользователя страница 59

Section 6

6.1

TECHNICAL CHARACTERISTICS

Functional Specifications

Process Fluid

Liquid, gas or steam.

Output Signal and
Protocol Communication

Two-wire, 4-20 mA controlled according to NAMUR NE43 Specification and with superimposed digital
communication (HART Protocol). See the figure below.

Power Supply

12 to 45 Vdc.

Load Limitation

250

0

12

20

30

40

45

1650
1500

1000

500

LO

A

D

[O

h

m

]

4-20mA AND

DIGITAL COMMUNICATION

4-20mA only

OPERATING AREA

POWER SUPPLY [Volt]

Indicator

Optional 4½-digit numerical and 5-character alphanumerical LCD indicator.

Hazardous Area
Certifications

Intrinsic Safe (FM, CSA, NEMKO, DEKRA/EXAM, CEPEL and NEPSI), non-incendive (FM, CSA and
CEPEL), explosion proof (FM, NEMKO and CEPEL) and dust ignition proof (FM).

European Directive
Information

Authorized representative in European Community

Smar Gmbh-Rheingaustrasse 9-55545 Bad Kreuzanach

PED Directive (97/23/EC) – Pressure Equipment Directive

This product is in compliance with the directive and it was designed and manufactured in accordance with
sound engineering practice using several standards from ANSI, ASTM, DIN and JIS.

EMC Directive (2004/108/EC) - Eletromagnetic Compatibility

The EMC test was performed according to IEC standard: IEC61326-1:2006, IEC61326-2-3:2006,
IEC61000-6-4:2006, IEC61000-6-2:2005. For use in environment only.
Keep the shield insulated at the instrument side, connecting the other one to the ground if necessary to
use shielded cable.

ATEX Directive (94/9/EC) – Equipment and protective systems intended for use in potentially
explosive atmospheres.

This product was certified according European Standards at NEMKO and EXAM (old DMT). The certified
body for manufacturing quality assessment is EXAM (number 0158).

LVD Directive 2006/95/EC – Electrical Equipment designed for use within certain voltage limits

According the LVD directive Annex II the equipment under ATEX “Electrical equipment for use in an
explosive atmosphere” directive are excluded from scope from this directive.

The EC declarations of conformity for all applicable European directives for this product can be found
at

www.smar.com

.

Temperature Limits

Temperature Limits

Ambient

-40

to

85 ºC

-40

to 185 ºF

-15

to

85 ºC

-59

to 185 ºF

LD290I

Process

-40

to

100 ºC

-40

to

212 ºF

Silicone Oil

0

to

85 ºC

32

to

185 ºF

Fluorolube Oil

-25

to

85 ºC

-13

to

185 ºF

Viton ‘Ring

-40

to

150 ºC

-40

to

302 ºF

LD290L

-15

to

150 ºC

-59

to

302 ºF

LD290I

Storage

40

to

100 ºC

-40

to

212 ºF

Digital
Display

-20

to

80 ºC

-4

to

176 ºF

Operation

-40

to

85 ºC

-40

to

185 ºF

without damage

Turn-on Time

Performs within specifications in less than 5 seconds after power is applied to the transmitter.

«
...
57
58
59
60
61
...
»

Содержание LD291





















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды