background image

Sending Unit Test:

Installing the sending unit on your rally car has always been a challenge.  Selecting the Sending Unit 
Test mode provides visual and audio feedback of when the sensor engages and releases each 
magnet.  This makes alignment of the magnets easy, and insures that you’re getting all of your pulses
all of the time.

Backlight On/Off:

Your 

ALFA

 has an adjustable backlight.  It may be turned on or off, has 5 brightness settings, and an 

automatic setting which preserves battery life.  

The best battery life is obtained when the backlight is 

completely OFF.  

The LCD display used in the 

ALFA

 is a type which has extremely good viewing 

characteristics with no backlighting while in normally lit situations.  The backlight is only necessary in 
darkness.

The best compromise is to use the AUTOMATIC backlight setting when you are running the 

ALFA

 on 

battery power.  This setting turns on the backlight for about 5 seconds whenever and switch is 
activated.  The default setting for the 

ALFA

 is Brightness 3 and AUTOMATIC.  

Note that you should only use the CONSTANT setting (either bright or dim) when running with the 12-
volt adapter!  Battery life will be extremely limited if the backlight is on constantly.

Time Synchronization:

The 

ALFA

 is equipped with 

Rally Link ™

 which allows one clock to read the time settings from 

another clock through an optional Sync Cable.  

No user input is required to sync two clocks

simply plug the marked end of the sync cable into the Master Clock, and the other end of the sync 
cable into the clock which needs to be set.  Within a few seconds, the two clocks will be in perfect 
sync – 

that’s all that’s required!

  Once the clocks are in sync, simply unplug the cable.

Your ALFA-Club will sync to older ALFA-Club and ALFA-Checkpoint clocks, as well as the newest 
version of the ALFA-Elite rally computer and ALFA-Pro advanced “B Unit”.

Options:

12 volt power cable and sending unit adapter

Sync cable

DIN adapter to use newer and older ALFA clocks to synchronize

Built in GPS receiver (Syncs time and provides alternate odometer input)

Timewise synchronization adapter

Basic Sending Unit (wheel mounted magnetic sensor with rare-earth magnets)

EZ-Pulse hub mounted (removable) sending unit

ALFA-Club Owners Manual

8

Содержание ALFA-Checkpoint












Отзывы: