manualshive.com logo in svg

Smach EFE 1500 A, Руководство пользователя

Поделиться
Скачать
Smach EFE 1500 A Скачать руководство пользователя страница 62

 

61 

EFE 2500 AP/APS/ANP/APH 

15. POSSIBLE FAILURES AND SOLUTIONS 

 

 
 

Attention

:  DO  NOT  ALLOW ANY TECHNICAL  MAINTENANCE  OR  REPAIRS  BEFORE 

DISCONNECTING THE FREEZER FROM THE POWER SUPPLY.  
 
If the solutions listed below in the Trouble Shooting guide do not resolve your operational 
problems, call an authorized service agent for further assistance. 

 
TROUBLESHOOTING GUIDE 

 

Problem 

Cause 

Solution 

1 

Machine does not run 

No electricity//power 

Check if plugged in and switch on at wall 
socket 

Head and/or Hopper cover 
aren’t closed. 

Ensure that, the head and hopper cover 
is closed. 

No mix in the hopper. 

Re-fill the hopper. 

There is voltage fluctuation. 

Plug off and wait for 30 seconds and 
plug on again.  
Check if there is another machine is 
connected in the same socket. 

2 

Compressor starts, then 
stops after a few 
seconds. 

a)  Air-cooled machine: No air 
circulation 
b)  Water-cooled machine: No 
water circulation 

a)Check the clearances around the 
machine. 
b)Check the water inlet, outlet and filter. 
Check that pipe is not squashed nor 
bent. 

3 

Machine fails to cut-off 
when running on SOFT 
or HARD mode 

a)  Air-cooled machine: Air 
circulation is restricted. 
b)  Water-cooled machine: 
Water circulation is restricted. 

a)Check the clearances around the 
machine. 
b)Check the water inlet, outlet and filter. 
Check that pipe is not squashed nor 
bent. 

Too much air in the freezer-
barrel 

Open Dispense head and drain-

off ½ 

liter of product. 

No mix in the Hopper 

Re-fill the Hopper 

4 

Machine works, but no 
product comes from the 
Dispense Head. 

Dispense head is blocked with 
ice. 

Place the machine onto Wash mode and 
allow the product to thaw. Remove 1 liter 
mix and re-start the machine. 

Mixing instuctions of Soft-serve 
was not followed 

Drain the machine and re-fill with proper 
mix. 

The frozen product is too hard 

Set the Control Dial to Wash mode and 
allow the product to soften. 

Pump is not working. 

Re-assemble the pump properly. Check 
all the parts assembled correctly. 

Scrapper blades didn’t 
assambled correctly. 

Re-assemble the beater. 

5 

Machine runs, but 
Product is too soft 

Mixing instuctions of Soft-serve 
was not followed 

Drain the machine and re-fill with proper 
mix. 

Machine remained idle without 
dispensing product for too long. 

Remove 1 liter of frozen product and 
allow the machine to recover. 

Too much frozen product is 
dispensed at a time. 

Allow the machine to recover; then 
continue to draw within the production-

Содержание EFE 1500 A





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды