background image

5

9

8

Mount Control Module to Wall

Control Module Connections

B

Insert Solenoid Valve Connector into the Modular
Receptacle on Connector Board. 

C

Insert Locking Connector from Faucet Spout into mating
Receptacle on Connector Board. Allow 3 to 4 inches (76
to 102 mm) of Cable to extend into the Control Module.

D

Insert each Conduit Cable into a strain relief slot in the
Control Module.

EXTENSION CABLES

Extension Cables are available as an option from Sloan to allow for installing the Control
Module remote from the Faucet Spout and Solenoid Valve. Refer to the Parts List for
available lengths.

B

Mount Control Module to wall using Mounting Screws and
Plastic Anchors.

A

Install the Control Module in an appropriate location.
Control Module must be installed so that all cables enter
from the bottom of the unit. When installed, Cables from
the Spout and Solenoid Valve to the Control Module
should have some slack.

A

Route Cables from Solenoid Valve and Spout to the
Control Module.

11

Plug In Transformer

A

Plug Transformer into 120 VAC Receptacle.

Start-Up

10

CONTROL

MODULE

ENCLOSURE

FROM SOLENOID

VALVE

FROM TRANSFORMER

STRAIN

RELIEF

SLOTS

FROM FAUCET

SPOUT

TERMINAL BLOCK - 

1. REMOVE TERMINAL

BLOCK

2. INSERT POWER

CABLES

3. SECURE WITH

SCREWS

4. REINSTALL TERMINAL

BLOCK

CONNECTOR

BOARD

POWER CABLE

4” (102 mm)

MODULAR

RECEPTACLE

A

Supply power to Transformer.

Note: The Control Module is equipped with two LED lights. When power is
supplied by the Transformer, one LED will illuminate green. When Sensor is
activated, this LED will change to red. A second red LED illuminates when
Solenoid Valve is activated.

B

Open Supply Stops. With Aerator removed, activate
Faucet for 30 seconds by placing hands in front of
Sensor. The Solenoid Valve should “click” and water
should flow from the Spout. If this does not occur, refer to
the Troubleshooting section of this installation instructions.

C

Close Supply Stop(s) and install Spray Head in Spout
using the Key provided. Reopen Supply Stop(s), activate
Faucet and check for leaks.

TRANSFORMER

Содержание Optima ETF-800









Отзывы: