manualshive.com logo in svg

Sleipner SX35, Руководство по установке

Поделиться
Скачать
Sleipner SX35 Скачать руководство пользователя страница 11

 11

5630

22

2021

-

SX35 & SX50

MC_0074

Grids or Cowls assembly

1.  Attach the cowls or grids with included bolts and washers. 

(NB: If installation of the cowls ensure the appropriate twist of the cowl to direct water  

  away from obstacles)

MG_0145

Tighten 2Nm

*Cowl

Tighten 2Nm

MG_0112

Align two ends of the tunnel. 

Remove cover guard.

Remove cover 

guard.

Remove cover 

guard.

Push two tunnel 

ends together. 

Check snap lock 

positions around the 

tunnel. 

Snap lock

Ensure top lips tabs 

into the motor 

inserts.

1

2

Tunnel Installation

1.  Ensure to remove the plastic cover guard on the tunnel.

2.  Connect both ends of the tunnel to the thruster motor. All hooks must be completely interlocked making the inside of the tunnel smooth. 

(NB: 

Ensure tunnel moulding around the gear leg and tunnel top align.)

 

MC_0074

!

 Please refer to the graphic for special considerations relating to your model 

!

IMPORTANT 

Ensure all snap-lock positions are correctly connected into place. 

Содержание SX35

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды