Skyworks UG499 Скачать руководство пользователя страница 3

Страница: 3 / 13

USER GUIDE

UG499: Si828x-AW-GDB Gate Driver Boards

Skyworks Solutions, Inc. • Phone [949] 231-3000 • [email protected] • www.skyworksinc.com

206359B • Skyworks Proprietary Information • Products and Product Information are Subject to Change without Notice

November 10, 2022

Function Block Diagram

Figure 2. Function Block Diagram

3. Pin Descriptions

3.1. Input I/O Connector (Low-Voltage JT3)

This connector is located in the center of the Si828x-AW-GDB. In the

XM3 Evaluation Tool

t est setup, the JT3 connector pro-

vides the I/O interface connections across the

Differential Transceiver Daughter Board Companion Tool

to the lab bench

instrumentations including power supply, function generator, control signals, etc. In the

XM3 Inverter Reference Design

, the

JT3 connector provides direction connection to the controll board, enabling the evaluation of the Si828x-AW-GDB in high
power inverter applications. Table 1 provides a complete list of the signals in the JT3 connector.

Содержание UG499














Результаты поиска

Содержание UG499

Отзывы:

Похожие инструкции для UG499

Бренды по названию

Популярные бренды

Skyworks UG499, Руководство пользователя

Результаты поиска

Содержание UG499

Отзывы:

Похожие инструкции для UG499

Бренды по названию

Популярные бренды