background image

15

V-ring

Frame

5.

 After attaching the first four Springs (8) in step 4, start 

from the first spring you attached in step 4. Count exactly 12 

V-rings and 12 frame holes in a clockwise direction. Attach 

another Spring to the V-ring and frame at this point. Count 

24 V-rings and 24 frame holes in a clockwise direction and 

attach another Spring. Count 24 V-rings and 24 frame holes 

in a clockwise direction two additional times and attach another 

two Springs. You will now have 8 evenly spaced Springs (8) 

attaching the jump mat (5) to the trampoline frame (not shown).

Attach eight Springs (not shown) evenly between the

eight attached Springs in the same manner as before. 

Attach sixteen Springs (not shown) evenly between the

sixteen attached Springs.

Continue to attach the remaining Springs between the

previously attached Springs, until all Springs are attached. 

Safety Note: For the jump mat (5) to have the even tension 

necessary for safety in jumping, the Springs (8) must be 

attached as described. As you attach Springs, carefully

count the V-rings and frame holes. If a V-ring or hole is 

skipped, reattach the Springs in the proper position.

6

. Lay the Frame Pad (6) on the frame. Adjust the posi-

tion of the Frame Pad so that the slits of the pad are just

above the holes of the socket of frame, as shown.

 

Inset drawing

9

Caution: Do not use the trampoline without the Frame Pad 

(6). The Frame Pad is designed to reduce the possibility of

injuries due to jumpers coming in contact with the tram-

poline frame. If you do not have a Frame Pad, contact

your dealer to obtain one. Properly install the Frame Pad

before using the trampoline.

7.

 Look underneath the trampoline.  Locate the straps 

attached to the underside of the frame pad. Position each outer 

strap so that one strap is on each side of the frame as shown. 

Tie the outside straps sewn to the Pad Joints to the near springs, 

and attach the inner straps to the near V-rings. 

Repeat this step with the remaining straps (not shown).

6

 Outer Straps

Frame

Strap sewn in the outside of

 the Joint for the pad bottom

Inner Straps

V-ring

5

8

6

3

Содержание SWTC1500













Отзывы: