Skyvue IGP-42-OB Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 24

background image

17

P

ost

t

ilt

M

ount

oBX 32000 / oBX 4270

|

1. With U-bolts threaded through the mounting plates, place

stainless steel flat washers over the bolt ends.

2. Place stainless steel lock washers over bolt ends.

3. Thread black powder coated nuts over bolt ends and hand tighten.

See figure 3a for suggested mounting plate placement.

4. Once positioned, level and tighten all U-bolt nuts on mounting

plate.

5. Place rubber bolt caps over exposed bolt ends

U-Bolts and

Mounting Plate Assembly Cont.:

«
...
17
18
19
20
21
...
»

Содержание IGP-42-OB

























Отзывы:

Нет отзывов

Похожие инструкции для IGP-42-OB

Бренд: NEC Страницы: 2

Бренд: NCR Страницы: 12

Бренд: La Vieille Garde Страницы: 4

Бренд: Garmin Страницы: 50

Бренд: Viking Страницы: 1

Бренд: Eminent Страницы: 2

Бренд: Magellan Страницы: 10

Бренд: Daewoo Страницы: 6

Бренд: Blaupunkt Страницы: 8

Бренд: OBERON Страницы: 3

Бренд: U-Line Страницы: 3

Бренд: Crestron Страницы: 2

5URAIL-2900-EARS

Бренд: Rackmount Страницы: 4

Бренд: Konig & Meyer Страницы: 4

Бренд: DeWalt Страницы: 16

Бренд: DeWalt Страницы: 19

Бренд: DeWalt Страницы: 15

Бренд: DeWalt Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды