THERMOSTAT FUNCTION
Press the
•
MODE
key until the LCD screen shows the word “THERMO” at the top of the screen.
To adjust set temperature, press the
•
UP
and
DOWN
buttons until the desired temperature is reached. The temperature range is
99ºF (32ºC) to 45ºF (6ºC).
If no button is pressed, the set temperature will automatically be accepted.
•
The flame icon will appear when the control calls for heat. The flame icon will disappear when the appliance reaches its set tem
-
•
perature.
Press the
•
MODE
key to disengage the Thermo Mode.
SETTING THE CLOCK
Hold the TIMER/TIME button for 3 seconds. The hour section of the time will begin flashing.
•
Select the hour by pressing the UP and DOWN buttons. If you go past 12 o’clock the AM and PM will change.
•
Once the hour is selected, press and release the TIMER/TIME button again, and the minute section of the time should be flashing.
•
Use the UP and DOWN buttons to scroll through the minutes.
•
Once the minutes are correct, press the set button or press and hold the TIMER/TIME button for 3 seconds. The time will lock.
•
SETTING THE COUNTDOWN TIMER
This remote control system can operate with a built-in countdown timer when the transmitter is in the ON or THERMO modes (THER-
MO or ON must be displayed on the screen).
Slide
Switch
OFF
REMOTE
ON
LEARN
VALVE
ANTENNA
REMOTE RECEIVER
Dry Contact
(2) 1/4” female
Connectors
To 110VAC
input
When plugged into a standard 110-120 VAC receptacle, the remote receiver operates on
commands from the transmitter or from the slide switch on the face of the receiver (This
switch is to be used during a power outage to operate the appliance manually).
ON
•
: will manually turn on the appliance.
REMOTE
•
: will allow use of handheld transmitter. If the system does not respond to the
transmitter on initial use, check the battery positions in the remote. If that does not work,
see the LEARNING TRANSMITTER TO RECEIVER section.
OFF
•
: will disable the remote receiver.
It is suggested that the slide switch be placed in the OFF position if you will be
•
away from your home for an extended period of time.
The remote receiver is manufactured with a “dry contact” relay in its circuitry that operates
like an on/off switch. However, no power or current passes from the 110-120 VAC input side
to the wires leading from the output side of the remote receiver.
RECEIVER
WARNING
This remote control system must be installed exactly as outlined in these instructions. Read all instructions completely before at-
tempting installation. Follow instructions carefully during installation. Any modifications of this remote control or any of its compo
-
nents will void the warranty and may pose a fire hazard.
Consult gas appliance manufacturer’s instructions and wiring schematics for proper placement of all wires. All electronic modules
are to be wired to manufacturer’s specifications.
The following wiring diagrams are for illustration purpose only. Follow instructions from manufacturer of gas valve and/or electronic
module for correct wiring procedures. Improper installation of electric components can cause damage to electronic module, gas
valve and remote receiver.
REV. 5-8-13 Page 2
Press and release the
•
TIMER
button. The minimum 0:15 minute setting on the LCD Screen will begin to flash.
Press the
•
UP
or
DOWN
button on the transmitter to chose your countdown time. Available countdown times are 15 min, 30
min, 45 min, and 1 hour to 9 hours (alternating every 30 min).
To initiate the countdown, press the
•
SET
button. If no button is pressed within 15 seconds, the setting will automatically be ac-
cepted. The system will return to OFF mode when the countdown time expires. If the system is in THERMO mode, it will cycle
on and off based on the set temperature until the timer expires.
THERMO UPDATING FEATURE
This remote control has a temperature updating feature built into its software. The transmitter reads the room temperature every 2 min-
utes, then updates the room temperature on the LCD screen.
NOTE:
The thermo feature operates the appliance whenever the room temperature varies a certain number of degrees from the set
temperature. This variation is called the “swing” or temperature differential. This feature lets the appliance turn off and on 2 ºF (1 ºC)
above or below the set temperature of the room. This is to cushion the number of times the appliance is turned on and off.
Skytech Smart Stat III
