REV. 3/19/05
Page 5 of 14
MANUAL CHECK OF “SWING” OR TEMPERATURE DIFFERENTIAL
The operation of the factory set “THERMO SWING” can be checked by adjusting the SET TEMP 2
0
F above or below the room
temperature. This will cause the system to turn ON or OFF. Normally the system will only respond to temperature changes every two
minutes. Manually changing the SET temperature will activate the system in less than 10 seconds. If the “SWING” is changed, then
anew room temperature differential will respond. Factory setting of SWING temperature is 2
0
F.
1.
To change the temperature “SWING” setting (1-3), press the AHEAD + BACK buttons simultaneously to display the current “SWING”
setting in the SET TEMP frame. The word SWING will display on the LCD screen.
2.
Press the UP or DOWN button to change the temperature differential or “SWING” (1-3). See above for 1-3 “SWING” temperature
values.
3.
To store the “swing number”, press the SET/RETURN button or allow 15 seconds to lapse, and the new “swing number” will be
automatically programmed.
NOTE: When the gas fireplace system is activated, a FLAME icon will display on the LCD screen indicating a signal has been sent from
the TRANSMITTER.
OPERATING INSTRUCTIONS
THERMO OPERATION
– (Systems operates thermostatically based on SET TEMP setting, ONLY)
SETTING DESIRED ROOM TEMPERATURE
This remote control system can be thermostatically controlled when the
transmitter is in the THERMO mode (THERMO must be displayed on the
screen).
1.
To set the DESIRED room temperature, press the MODE button to place the
transmitter into THERMO mode. THERMO ON or OFF will display.
2.
Then press the UP or DOWN button to select the DESIRED room
temperature. The highest SET temperature is 99
0
F (32
0
C). The lowest
SET temperature is 45
0
F (6
0
C).
3.
The TRANSMITTER will “sense” the room temperature every two minutes
automatically turning the fireplace ON or OFF thermostatically.
MANUAL CHECK OF THERMO OPERATION
The operation of the Thermo setting can be checked on demand by adjusting the SET temperature 2
0
F above or below the room temperature,
which will cause the system to turn ON or OFF, respectively. Normally, however, the system will only respond to temperature changes every
two minutes. NOTE: if “SWING” number has been changed, then activation will occur at the new “SWING” setting.
TEMPERATURE OVERRIDE
– (Operates only in PROGRAM mode)
The user may change the current SET temperature without changing the
programs stored in the transmitter’s memory. The OVERRIDE feature will be
automatically cancelled at the start of the next PROGRAM PERIOD.
1.
To change current SET TEMP, press the UP or DOWN button. (Setting will
be cancelled automatically when next program period begins.) The
word OVERRIDE will appear over the SET frame on the LCD.
2.
To cancel temperature OVERRIDE, press SET button.
TEMPERATURE HOLD
– (Operates only in PROGRAM mode.)
The user may override the SET temperature during any period, adjusting the
SET temperature to a CONSTANT new SET/HOLD temperature.
1.
Press the UP or DOWN button to change the SET temperature to the level
desired. The word OVERRIDE will appear in SET frame on the LCD.
2.
To HOLD the new temperature at a CONSTANT setting, push the UP and
DOWN buttons TOGETHER to activate the HOLD function. The word HOLD
will appear over the SET frame and the word OVERRIDE will disappear.
3.
To cancel OVERRIDE or HOLD, press the SET button.
1
MO
EVE
ON
THERMO
2
TEMP
FLAME
SET
FAN
O F F
O F F
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
2
1
TEMP
SET
MO
DAY
PROGRAM
OVERRIDE
ON
FLAME
FAN
OFF
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
3
1,2
TEMP
SET
MO
DAY
PROGRAM
HOLD
ON
FLAME
FAN
OFF
UP
DOWN
MODE
TIMER
TIME
SET
PROG
AHEAD
BACK
FAN
