Operation
Push button
Timer / Learn LED
Loss of Signal LED
Learn button
Lock button
Antenna
Keypad Transmitter
To operate the garage door opener, enter the password and [#].
The factory default password is [0][0][0]. Therefore to activate the
Garage One
TM
receiver GT-100R with the keypad transmitter, simply enter
[0][0][0][#].
Follow the instructions below to change the factory default password.
Changing Password
To change a password, you must have the master password, which is
the password that allows setting additional password. Up to 3 second-
ary passwords can be assigned to each keypad transmitter. Therefore,
the total number of password is:
1 Master Password (Programming and Operation)
3 Secondary Password (Operation Only)
3. OPERATION
To change the master password, follow the instructions
below:
To change the password, follow the instructions below:
1. Enter the current password (000 is the factory default password)
2. Press [*]
3. Press [0]
4. Press [*]
5. Enter the new password (password can be from 3 to 6 digits)
6. Press [*]
If the keypad transmitter accepts the new password, it will a long beep.
If it emits 3 short beeps, it means the password has not been changed.
Start again from step 1.
To assign or change secondary password, follow the
instructions below:
1. Enter the current master password (000 is the factory default
password)
2. Press [*]
3. Press the numeric key that represents the secondary password
user, either [1], [2], or [3].
4. Press [*]
5. Enter the new secondary password (password can be from 3 to 6
digits)
6. Press [*]
If the keypad accepts the new secondary password, it will emit a long
beep. If it emits 3 short beeps, it means the password has not been
assigned or changed. Start again from step 1.
To delete a secondary password, follow the instructions below:
1. Enter the current master password (000 is the factory default
password)
2. Press [*]
3. Press the numeric key that represents the secondary password
user, either [1], [2], or [3].
4. Press [*]
5. Press [*] again
If the secondary password is successfully deleted, it will emit a long
beep. Otherwise, start from step 1 again.
Learn Button
To program Skylink’s remote control / sensor
1. Press the learn button for approx. 5 seconds.
2. The “Timer / Learn” red LED will be on, release the learn button.
3. Activate the Skylink
®
remote control. If the Skylink
®
remote control has
multiple buttons, press the button you would like to operate.
4. The “Timer / Learn” LED will be off after it has successfully programmed
the remote control.
5. You can now press the programmed remote to operate the garage
door opener.
Erase Skylink
®
remote controls / sensors
To erase unwanted remote control(s), first erase all remote controls and
sensors, then program the ones you would like to keep.
Erase all remote controls / sensors
1. Press and hold the learn button for 15 seconds.
2. The “Timer / Learn” red LED will flash rapidly meaning all remote have
been erased.
3. You have now successfully erased all the remote controls and sensors.
Follow the instructions “To program Skylink’s remote control” to add the
remote control(s) you would like to keep.
Push Button
Press the push button to open or close the garage door.
Lock Button
Lock feature is designed to prevent Skylink
®
handheld
remotes such as Skylink
®
Keychain Remote Model 4B-201
(sold separately) to operate the garage door opener.
To activate the lock feature
1. Press and hold the lock button for approx. 2 seconds, then release it.
2. When the lock feature is activated, the red LED underneath the push
button will flash rapidly.
Note: If a valid wireless remote signal is received while the lock feature is
activated, Garage One
TM
will beep to reminding you the Garage One
TM
is
locked.
To deactivate the lock feature
1. Press and hold the lock button for approx. 2 seconds, then release it.
2. When the lock feature is deactivated, the red LED underneath the
push button will flash slowly indicating the Garage One
TM
is in normal
operating mode and the lock feature is deactivated.
3. OPERATION (CONT)