manualshive.com logo in svg

SkyLink DIAL-ALERT AD-105 Guide, Руководство пользователя, Страница: 12 / 14

Поделиться
Скачать
SkyLink DIAL-ALERT AD-105 Guide Скачать руководство пользователя страница 12

–

22

–

ADVANCED PROGRAMMING

DIAL-ALERT QUICK GUIDE

[PIN]+[PROG]+[1]

[PIN]+[PROG]+[2]

[PIN]+[PROG]+[3]

[PIN]+[PROG]+[4]

[PIN]+[PROG]+[5]

[PIN]+[PROG]+[6]

[PIN]+[PROG]+[7]

[PIN]+[PROG]+[8]

[PIN]+[PROG]+[9]

Operating Mode

Change Password

Voice Message Recording

Phone Number

Program Sensors / Transmitters

Erase Sensors / Transmitters

Calling Time

Entry / Exit Delay

Pick up Pause

2

0000

N/A

N/A

N/A

N/A

45 sec.

Instant

5 sec.

[1] - Sensor Mode, [2] - SC-001 Mode

Any 4-digit password

[0] - Main Message, [1-6] - Secondary Messages

[1-9] Up to 9 phone numbers

Program up to 16 sensors / transmitters

Erase all sensors / transmitters

[1]-30, [2]-45, [3]-60, [4]-75, [5]-90 seconds

[1] - Instant, [2]-30, [3]-45, [4]-60, [5]-75 seconds

[1] - 1 sec, [2] - 2 seconds....... [9] - 9 seconds

[PIN]+[PROG]+[*1] Universal Dial Tone

1

[1] - Off, [2] - On

Factory
Default

Settings

Functions

Program #

CONNECT THE DIAL-ALERT WITH YOUR EXISTING ALARM SYSTEM

You may connect your existing alarm system with the 

Dial-Alert

 so that the dialer

will be triggered by your alarm system when it is activated. There are 2 ways you
can connect your dialer with your existing alarm system.

1. Connect the dialer with the alarm system
     using hard wire (normally closed).

2. Connect the dialer with the alarm system
     using the Audio Sensor (AS-101).

Follow the diagram below for hardwiring
the dialer with the existing alarm system.
Every time the alarm system is activated, it will automatically trigger the dialer
to dial out all the preset telephone numbers and play the pre-recorded message.

The other way to trigger the dialer by the existing
alarm system is to use the Audio Sensor AS-101
in conjunction with the 

Dial-Alert

, (see Additional

Accessories page 24).

PANEL OR SENSOR

N.C.. LATCHING

DRY CONTACT*

(NORMALLY CLOSED

OPENS ALARM)

AD-105

Remove the

jumper first

Place the Audio Sensor beside the siren of your
existing alarm system, once the alarm is activated,
the siren will sound and the Audio Sensor will be
triggered and send a signal to the 

Dial-Alert 

to

activated it. There is no wiring involved in this case.

Remove the jumper first

The AD-105 

Dial-Alert

 comes with 1 battery that at some point you may

have to replace:

One

9 volt alkaline battery for the 

Dial-Alert

Recommendation: Test your 

Dial-Alert

 periodically to ensure that the battery

is working.

Dial-Alert Battery

The 

Dial-Alert

 comes equipped with a 9V backup battery in case the elec-

trical power is interrupted for any reason.

When the dialer backup battery is low, the LOBATT. light goes on.

To replace the dialer backup battery:

1.   Undo the two screws on the back of the
      

Dial-Alert

.

2.   Open the 

Dial-Alert

 case by pressing

      down on the two tabs on the top edge
      and pull the front forward.

3.   Disconnect the old battery.

4.   Connect the new battery.

5.   Close the 

Dial-Alert 

case and re-insert the

      two screws.

The battery life, (9 volt alkaline battery), is approximately two years if used
only for backup.

–

23

–

BATTERY MAINTENANCE

Содержание DIAL-ALERT AD-105 Guide















Отзывы:

Нет отзывов