manualshive.com logo in svg

Skyjack 3219 SJIII Compact Series, Руководство по эксплуатации

Поделиться
Скачать
Skyjack 3219 SJIII Compact Series Скачать руководство пользователя страница 56

Maintenance Support Procedure 

Section 3 - Operation

3.12  Maintenance Support Procedure

This section provides the operator with procedure 
regarding deployment and storage of maintenance 
support. 

The maintenance support is a safety mechanism 
designed to support the scissor assembly. When 
properly positioned it can support the scissor assembly 
and empty platform. The maintenance support must 
be used when inspection and/or maintenance is to be 
performed within the lifting mechanism.

WARNING

The maintenance support must be used 
when inspection and/or maintenance or 
repairs are to be performed within the 
lifting mechanism. Failure to use this 
safety mechanism could result in death 

or serious injury.

1

Figure 3-17. Maintenance Support

To Deploy the Maintenance Support

1. 

Remove all material from platform.

2. 

Raise platform until there is adequate clearance to 
swing down maintenance support (item 1).

3. 

Swing maintenance support down from storage 
bracket into a vertical position.

4. 

Remove hands and arms from scissors area.

5. 

Lower platform until bottom end of maintenance 
support contacts the labeled cross bar and 
scissors are supported by maintenance support.

6. 

Turn main power disconnect switch to “ ” off 
position. 

To Store the Maintenance Support

1. 

Turn main power disconnect switch to “ ”on 
position.

 

2. 

Raise platform until there is adequate clearance 
to swing up the maintenance support.

3. 

Swing bar fully up into storage bracket.

4. 

Lower the platform.

WARNING

Do not reach through the scissor 
assembly when the platform is raised 
without the maintenance support properly 
positioned. Failure to avoid this hazard 

could result in death or serious injury. 

Page 56

SJIII DC Electric

Содержание 3219 SJIII Compact Series









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды