Skyjack 3219 SJIII Compact Series Скачать руководство пользователя

Страница: 54 / 104

Moving the Aerial Platform Through a Doorway

Section 3 - Operation

3.11 Moving the Aerial Platform Through a

Doorway

WARNING

This procedure is suitable for level

ground only.

Confirm that the height/width of the doorway
is sufficient to allow the aerial platform to pass
through.

NOTE

If it is necessary to fold the guardrails,
refer to

Section 3.9

for guardrail folding

procedure.

Perform a thorough job site inspection prior to
operating the aerial platform to identify potential
hazards in your work area.

Cordon-off the pathway which you intend to
travel.

Position the aerial platform to allow all future
motion, including through the doorway, to be in
a forward direction.

Turn main power disconnect switch to “ ” off
position.

Use the ladder of aerial platform to access
platform.

WARNING

Ensure that you maintain three points of
contact when using the ladder to mount/

dismount platform.

Close the gate. On platform control console, push
in “

” emergency stop button.

Disconnect and remove platform control console
from the platform.

Fold the guardrails if necessary. Refer to

Section

3.9

for guardrail folding procedure.

10. Use the ladder to dismount from platform.

11. Connect platform control console to the connection

at the rear of the base.

NOTE

For some models, the connection is located
beneath an access panel which requires that

the scissor assembly be raised to access it.

12. Ensure there are no personnel in the intended

path of travel.

13. Notify those around the pathway that you will be

moving the aerial platform.

14. Use a spotter to guide movement. Ensure the

spotter remains at a safe distance.

15. Ensure that platform control console is properly

oriented in the direction the aerial platform is
facing.

16. Turn main power disconnect switch to “ ”on

position.

17. On base control console, pull out “

” emergency

stop button.

18. Select base/off/platform key switch to “

”

platform position.

19. On platform control console, pull out

“

” emergency stop button.

20. Select lift/off/drive switch to “

” drive position.

Select inclined drive/level drive switch to “

”

inclined drive (low speed/high torque) position
for reduced speed.

WARNING

Do not drive the aerial platform toward

yourself.

21. Using as low a speed as practical and the operator

positioned behind the aerial platform, drive
forward through doorway.

Page 54

SJIII DC Electric

Содержание 3219 SJIII Compact Series









































































































Результаты поиска

Содержание 3219 SJIII Compact Series

Отзывы:

Похожие инструкции для 3219 SJIII Compact Series

Бренды по названию

Популярные бренды

Skyjack 3219 SJIII Compact Series, Руководство по эксплуатации

Результаты поиска

Содержание 3219 SJIII Compact Series

Отзывы:

Похожие инструкции для 3219 SJIII Compact Series

Бренды по названию

Популярные бренды