SkyAzúl MicroGuard 534 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 24

SkyAzúl MicroGuard 534 Скачать руководство пользователя страница 22

Figure 1−89
Calibration And Diagnostic Screen

CALIBRATION AND DIAGNOSTICS

ERROR CODES

ENTER CALIBRATION

Message

Data

Count

A00 B0 C00 D00

System Fault Codes

If faults in the system are detected during a test, the
warning message area will show the words SYSTEM
FAULT. If the words SYSTEM FAULT occur, press the
Display/Select button to display the Calibration And
Diagnostic screen. On the Calibration And Diagnostic
screen, press the Error Code button to display error
codes in the box at the top of the screen. This informa-
tion can then be used to assist the service technician in
determining the fault. Contact your distributor for as-
sistance with the fault codes.

Calibration

If the system requires calibration, contact you distribu-
tor for assistance. Calibration must be done by a quali-
fied technician. Press the Display/Select button to dis-
play the Calibration And Diagnostic screen. On the
Calibration And Diagnostic screen, press the Enter
Calibration button. The calibration screen will be dis-
played and prompt a calibration key sequence to begin
the calibration routine.

MicroGuard 534

Operator's Manual

SkyAzúl, Equipment Solutions

www.skyazul.com
16

301-371-6126

«
...
20
21
22
23
24
»

Содержание MicroGuard 534

























Отзывы:

Нет отзывов