background image

                                                  Assembly and Operating Manual                                                  G202-3D 

  13 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figs. 37 -39    Function test 

 

Check the channel assignment at the receiver, and if 

necessary swap the plugs as necessary. 

- Set the transmitter sticks and trims to centre. 

- The control surfaces should now also be at centre (neutral). 

Adjust the clevis where necessary. 

- Check the direction of rotation of the servos. 

- Stand behind the model. - When you move the rudder stick 

to the right, the rudder should also deflect to the right. 

- Pull the elevator stick back towards you, and the rear edge 

of the elevator should rise. 

- Moving the aileron stick to the right, you MUST check that 

the trailing edge of the right aileron rises, the left aileron 

should go down. 

- If any function works the wrong way round, correct it using 

the servo reverse facility on your transmitter. 

- Set the control throw using the transmitter servo end point 

adjustment function. 

- The travels are measured at the inboard end of the control 

surfaces. 

- The stated control throws are just a guide for the first few 

flights. You will probably need to adjust the actual settings 

to suit your individual flying style. 

- The Expo settings should also be adjusted to suit the pilot's 

preference. 

 

 

 

 

 

 

 

 

 

 

 

38

37

39

Содержание G202-3D

















Отзывы: