background image

Fig. 7.1f

Fig. 7.1g

Fig. 7.1h

PART VII: Proper Care for Your Telescope

19

7.2 Cleaning Your Telescope

Replace the dust cap over end of telescope whenever not in use. This prevents dust from 
settling on mirror or lens surface. Do not clean mirror or lens unless you are familiar with 
optical surfaces. Clean eyepieces with special lens paper only. Eyepieces should be han
dled with care, avoid touching optical surfaces.

Secondary 

mirror

Primary mirror

stop and keep your 

hand here

collimating cap in

Aligning the Primary Mirror

There are 3 large bolts and 3 small screws at the back 

of your telescope. The large bolts are the adjusting 

screws and the small screws are the locking screws 

(Fig.7.1f). Loosen the large bolts by a few turns. Now 

run your hand around the front of your telescope 

keeping your eye to the focuser, you will see the 

reflected image of your hand. The idea here being to 

see which way the primary mirror is defected, you do 

this by stopping at the point where the reflected image 

of the secondary mirror is closest to the primary 

mirrors’ edge (Fig. 7.1g).
When you get to that point, stop and keep your hand 

there while looking at the back end of your telescope, 

is there an adjusting screw there? If there is you will 

want to loosen it  (turn the screw to the left)  to bring 

the mirror away from that point. If there isn’t a adjust-

ing screw there, then go across to the other side and 

tighten the adjusting screw on the other side. This will 

gradually bring the mirror into line until it looks like 

Fig.7.1h. (It helps to have a friend to help for primary 

mirror collimation, Have your partner adjust the 

adjusting screws according to your direction while you 

look in the focuser.)
After dark go out and point your telescope at a bright 

star, and put the high power eyepiece (10mm) in the 

focuser. Keep that bright star well centred in the 

middle of the eyepiece image. Check now the collima-

tion by looking at its airy disk as described (fig. 7.1a). 

If it is not symmetric, you can improve the symmetry 

by acting on the adjustment screws of the primary 

mirror in a similar way as what you did in daytime to 

achieve the symmetry of fig. 7.1h.
Once the symmetry is there, then collimation is done 

and the locking screws can be tightened to make the 

adjustment permanent.

Содержание VIRTUOSO GTi





















Отзывы: