manualshive.com logo in svg

Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2, Руководство пользователя, Страница: 54 / 56

Поделиться
Скачать
Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 Скачать руководство пользователя страница 54

4O3A Signature – Antenna Genius User Manual

 

Index

 

 

 

Page 

53

 of 

55

 

 

12. 

TROUBLESHOOTING 

12.1. 

Re-riving a bricked device 

The most typical scenario of bricking an AG is interrupting a firmware upgrade or failing a 
firmware upgrade due to a bad network connection. 

 

AG features a bootloader software enabling you to reinstall the firmware at any time.

 

The bootloader uses a fixed IP address – 192.168.1.250 so make sure your network is using the 
same subnet.

 

 

Follow these steps to take to reinstall firmware on a bricked device:

 

 

1.

 

remove DC power from AG

 

2.

 

move DIP 8 to ON position

 

3.

 

turn DC power back on

 

4.

 

Open the app, add a new device in the remote tab

 

5.

 

set name to anything and the address to 192.168.1.250. Click 

Save

 

6.

 

connect to this device

 

7.

 

the app will keep saying "unable to connect". Don’t worry, this is expected

 

8.

 

click 

Configure

, then in the drop down menu choose 

Upgrade firmware

 

9.

 

click 

UPGRADE

 

10.

 

wait for the progress bar to fill up 

 

11.

 

move DIP 8 to to OFF position

 

12.

 

remove DC power from AG

 

13.

 

turn DC power back on

 

 
 
 

 

Содержание 4O3A Signature Antenna Genius 8x2 Plus v2

























































Отзывы:

Нет отзывов