Skil Masters 3855, Инструкция по эксплуатации

Страница: 20 / 20

20
• Checking/adjusting of 90° fence alignment
∞
! disconnect the plug
- rotate the saw table to the 0° position and lock in place
- lower the tool arm and lock in place
- check for a 90° angle between blade and fence L with
a square (ensure the square contacts the saw blade
body and not its teeth)
- if necessary, adjust the 90° fence alignment as follows:
1) loosen 4 hex screws L1
2) adjust fence until blade and fence have full contact
with the square
3) tighten 4 hex screws L1
• Cable storage
§
APPLICATION ADVICE
• Special workpieces
- ensure that curved or round workpieces are especially
secured against slipping
- at the cutting line no gap may exist between the
workpiece and the fence or saw table
- if necessary, fabricate a special fixture
• For working with floor mouldings illustration
≥
can be
used as reference
• Always face the good side of the workpiece down to
ensure minimum splintering
• Only use sharp saw blades of the correct type
- quality of cut improves by the number of teeth
- carbide tipped blades stay sharp up to 30 times longer
than ordinary blades
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially the
ventilation slots at the back-end of the motor housing)
! disconnect the plug before cleaning
• Clean saw blade immediately after use (especially from
resin and glue)
! the saw blade becomes very hot during use;
do not touch it before it has cooled down
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol
•
will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 61029, EN 61000,
EN 55014, in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC
• Technical file at : SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
Jan Trommelen
Approval Manager
01.11.2010
NOISE/VIBRATION
• Measured in accordance with EN 61029 the sound
pressure level of this tool is 93 dB(A) and the sound
power level 106 dB(A) (standard deviation: 3 dB),
and the vibration < 2.5 m/s² (hand-arm method;
uncertainty K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 61029;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintainted accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work patterns
Scie à onglets radiale 3855
INTRODUCTION
• Cet outil est une machine fixe, conçue pour effectuer dans
le bois des coupes droites longitudinales et transversales
ainsi que des angles d’onglet (il est possible de réaliser
des angles d’onglet horizontaux de -47° à +47° et des
angles de biseau verticaux de 0° to 45°)
• Lisez et conservez ce manuel d’instruction
2
• La séquence des numéros apparaissant sur la fiche
d’instructions d’assemblage séparée correspond à la
séquence des étapes à suivre pour le montage de l’outil
• Utilisez uniquement l’outil lorsqu’il est tout à fait
assemblé correctement (veuillez noter que Skil ne peut
être tenue responsable de dégâts à l’outil et/ou de blessures
personnelles résultant du montage incorrect de l’outil)
• Avant d’utiliser cet outil pour la première fois, collez
l’autocollant fourni dans votre langue sur le texte anglais
de l’étiquette d’avertissement A
5