background image

18

•  SKIL can assure flawless functioning of the tool only 

when the correct accessories are used which can be 

obtained from your SKIL dealer

•  For mounting/using non-SKIL accessories observe the 

instructions of the manufacturer concerned

•  Use only accessories with an allowable speed matching 

at least the highest no-load speed of the tool

•  Never use saw blades made of high speed steel (HSS)

•  Do not use a saw blade which is cracked, deformed or dull

•  Only use saw blades with a hole diameter which fits the 

tool spindle without play; never use reducors or adaptors 

to fit large-hole saw blades

•  Protect accessories from impact, shock and grease

DURING USE

•  Do not force the tool; apply light and continuous pressure

•  Keep fingers, hands and arms away from the 

rotating saw blade 

3

•  Push spindle-lock button only when tool is at a standstill

•  When slotting, ensure that the saw blade does not get 

jammed in the workpiece

•  If the saw blade becomes blocked, switch off the tool 

immediately and disconnect the plug; only then remove 

the wedged workpiece

•  In case of jamming or electrical or mechanical 

malfunction, immediately switch off the tool and 

disconnect the plug

•  If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug

•  Never use the tool when cord is damaged; have it 

replaced by a qualified person

LASER RADIATION

• 

Do not look into the laser beam (laser radiation)

 

4

• 

Do not point the laser beam at persons or animals

•  Do not use any magnifying optical tools (such as 

magnifying glasses, telescopes, or binoculars) 

 

to view the laser beam

•  Do not operate the tool in the presence of flammable 

liquids, gases or dust

•  Do not operate the tool with children around

•  Do not replace the installed laser with another laser type

AFTER USE

•  After switching off the tool, never stop the rotation of the 

accessory by a lateral force applied against it

•  Only remove cut-offs or other parts of the workpiece from 

the cutting area when all moving parts have come to a 

complete standstill

•  The saw blade becomes very hot during use; do not 

touch it before it has cooled down

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

•  If for any reason the old plug is cut off the cord of this tool, 

it must be disposed of safely and not left unattended

USE

•  Transport/working position 

6

For releasing the tool (

working

 position)

-  press handle B 

5

 downward with one hand while pulling 

out locking pin C with the other hand, rotating it 1/4 turn 

in either direction and releasing it in that position

-  guide the tool arm slowly upward

-  for sawing with slide movement loosen locking knob R

For securing the tool (

transport

 position)

-  slide the tool arm to the stop in the direction of fence 

 

L and tighten locking knob R

-  press safety lever D 

5

 while lowering the tool arm with 

handle B to the stop

-  release safety lever D and hold handle B downward 

with one hand while pulling out locking pin C with the 

other hand, rotating it 1/4 turn in either direction and 

releasing it in that position

-  use transport handle E 

5

 for carrying the tool

•  Mounting tool on working surface 

7

!  for safe handling always mount tool on a flat and 

stable working surface (e.g. workbench)

-  use 4 mounting holes F for attaching the tool with 

suitable screws to the working surface

-  you may also clamp the tool to the working surface 

with commercially available screw clamps

-  for stabilizing the tool the height of support foot G can 

be adjusted

•  Dust/chip extraction 

8

-  mount dustbag H/vacuum cleaner as illustrated

-  empty dustbag regularly for optimal dust pick-up 

performance

!  never let the vacuum cleaner hose interfere with 

the lower guard or the cutting operation

•  Saw table extension 

9

-  use knobs J1 to fasten extension bars J (on either side 

of the tool)

-  the length of extension bars J is steplessly adjustable 

from minimum to maximum

•  Clamping the workpiece 

0

!  for optimum working safety always firmly clamp 

the workpiece with the adjustable clamp supplied

-  do not work with workpieces that are too small to clamp

!  for maximum workpiece dimensions use table 

!

 

as reference

For vertical clamping 

0

a

-  fasten assembled clamp into support hole K1 with 

knob K2 (on either side of the tool)

-  press the workpiece firmly against fence L

-  adapt clamp to the workpiece with knob K3

-  firmly clamp the workpiece by turning down knob K4

For horizontal clamping 

0

b

-  remove clamp from holder using knob K5

-  position clamp into support hole K6 as illustrated 

 

(on either side of the tool)

-  press the workpiece firmly against fence L

-  firmly clamp the workpiece by turning down knob K4

•  Setting mitre angles 

@

-  loosen locking handle M

-  rotate the saw table to the left or right and set the desired 

mitre angle (from 0° to 47°) by using indicator M1

-  tighten locking handle M (

do not tighten the handle 

too firmly

)

-  for quick and precise setting of often used mitre angles 

(0°, 15°, 22.5°, 30°, 45°) the saw table clicks into place 

at the corresponding positions

•  Setting bevel angles 

#

-  loosen three-legged knob N

-  swing the tool arm to the left until bevel angle indicator 

N1 points to the desired bevel angle

-  hold the tool arm in this position and tighten knob N

Содержание Masters 3855





















Отзывы: