OPERATION
1.
Use the following procedure to test the system before each use.
a.
Press Battery-Test button. If alarm is weak or fails to sound,
replace 9-volt battery and press button again. If alarm is still weak or
fails to sound, discontinue use of alarm.
b.
Seat patient and secure belt by placing the magnet (located
under red loop) over metal strip. (Illustration 3) Battery indicator light
should flash. If light fails to flash, replace battery and make certain that
the telephone-style plug is securely connected to the alarm unit. Retest.
If battery indicator light still fails to flash, discontinue use of system.
c.
Open magnetic closure. Alarm will sound. Secure closure.
Alarm will silence itself. It is now in the monitoring mode. If alarm fails
to sound when magnetic
closure is opened, check
plug connection and/or
replace battery. Retest. If
alarm again fails to
sound, discontinue use
of system.
2.
Select high or low vol-
ume.
3.
Alarm is activated
when patient opens the
magnetic closure. Press
the Auto-Reset button to
silence the alarm. The
alarm is now in stand-by
mode. Do not secure the magnetic closure when the system is not
being used to monitor a patient. Securing the closure will cause the
battery indicator light to flash and shorten battery life.
4.
The alarm will automatically go into the monitoring mode when the
magnetic closure is secured.
There is no on/off switch.
5.
After the closure is secured, adjust the belt to a proper fit around
patient’s hips.The wheelchair user may easily release the belt by plac-
ing his/her hand through the red loop and pulling up on the end.
with E-Z Release Velcro
®
Belt Alarm
29 Wells Avenue
914-963-2040
Yonkers, NY 10701
800-431-2972
Model # Description
Guarantee Unit
909393
E-Z Release Velcro
®
Belt Alarm One Year
Each
INSTALLATION
1.
Remove the rearmost screws
from the left and right sides of
the wheelchair seat. Insert the
screws through the grommets
on the ends of the two belt sec-
tions. Refasten screws to the
wheelchair. (Illustration 1)
2.
Place the telephone-style
connector cord through the
space between the wheelchair
seat and backrest. Make certain
that it is away from wheels and
other moving parts.
3.
Insert telephone-style plug into
Modular Receptacle on right side
of alarm. (Illustration 2) Alarm will
sound. Press Auto-Reset to
silence alarm.
Advanced design for nursing and therapy.
TM
Alarm system made in China. Instructions printed in USA.
Visit us online
at Skil-Care.com
1
2
3
MultiPro/ChairPro E-Z Releas.Qk 4/3/06 9:38 AM Page 1
Mounting Bracket
LED
A
B
C
D
E
F
Fig. 1
Fig. 2
Model # Description
Size
Unit
909371
ChairPro E-Z Release
Universal Each
Belt Alarm
GUARANTEES
1.
The ChairPro E-Z Release Belt Alarm Unit is replace-
ment guaranteed for one year following the date of pur-
chase.
2.
The E-Z Release belt with Velcro
®
closure and mag-
netic switch is replacement guaranteed for one year fol-
lowing the date of purchase.
These guarantees cover defects in materials and work-
manship under conditions of normal use. Please return
defective part to dealer from whom it was purchased. The
dealer will send the defective part to Skil-Care and
arrange for shipment of a replacement.
PURPOSE
The ChairPro E-Z Release Belt Alarm is a non-restrictive
wheelchair safety belt with integral magnetic alarm
switch. It is designed to alert caregivers when a patient
attempts to leave or has fallen from the wheelchair.
CAUTIONS
1.
The ChairPro E-Z Release Belt Alarm is not a substi-
tute for proper supervision. Fall-risk residents/patients
should be monitored regularly.
2.
Check battery each time alarm is used. If weak,
replace the 9-volt battery.
3.
LED should flash when the magnetic switch is
engaged. If LED fails to flash, check battery. Replace if
necessary. If LED fails to flash after battery has been
replaced and the plug is determined to be properly con-
nected, discontinue use of device.
29 Wells Avenue
914-963-2040
Yonkers, NY 10701
800-431-2972
1.
Insert enclosed cord
loop through bracket
hole. (Illustration B)
2.
Hang from wheel-
chair push-handle
(Illustration C)
B
C
Continued on reverse side.
R
es
traint-Fr
e
e
T
M
Cord Loop
INSTALLATION
Alarm Unit
You may choose one of the following two ways to attach
the alarm unit to the wheelchair.
Mounting Bracket
1.
Remove the second-
from-top screw from either
the left or right side of the
wheelchair backrest.
2.
Remove grommet from
screw, place the screw
through hole on alarm unit
mounting bracket, and
fasten screw to
wheelchair backrest.
(Illustration A)
A
ChairPro Safety Alarm
Auto-Reset
Battery
Test
Test battery before each use. If
weak, replace with 9-volt battery.
LED must glow when alarm is in
use. If not, replace battery.
High
Low
Mini-Phone
Plug
Modular
Receptacle
Mounting Bracket
LED
Alarm unit made in China. Instructions printed in USA.
E-Z RELEASE BELT ALARM
GUARANTEES
1. The E-Z Release belt with Velcro
®
closure and magnetic switch is
replacement guaranteed for one year following the date of purchase.
These guarantees cover defects in materials and workmanship under
conditions of normal use. Please return defective part to dealer from whom
it was purchased. The dealer will send the defective part to Skil-Care and
arrange for shipment of a replacement.
PURPOSE
The ChairPro E-Z Release Belt Alarm is a non-restrictive wheelchair safety
belt with an integral magnetic alarm switch. It is designed to alert caregivers
when a patient attempts to leave the wheelchair.
CAUTIONS
1. The ChairPro E-Z Release Belt Alarm is not a substitute for proper
supervision. Fall-risk and wander-risk patients or residents should
be monitored regularly.
2. Check battery each time alarm is used. If weak, replace the “AA” battery.
3. LED should flash when the magnetic switch is engaged. If LED fails to
flash, check battery. Replace if necessary. If LED fails to flash after battery
has been replaced and the plug is properly connected, discontinue use
of device.
INSTALLATION
Alarm Unit
You may choose one of the following two ways to attach the alarm unit to
the wheelchair.
Attachment of Alarm Unit
Mounting Bracket
1. Remove the second-from-top screw from either the left or
right side of the wheelchair backrest.
2. Remove grommet from screw, place the screw through
hole on alarm unit mounting bracket, and fasten screw to
wheelchair backrest. (Illustration A)
1. Insert enclosed cord
loop through bracket hole.
(Illustration B)
2. Hang from wheel-
chair push-handle
(Illustration C)
SEAT BELT INSTALLATION
WHEELCHAIR BELT INSTALLATION (Grommet)
1. Remove the rearmost screws
from the left and right sides of the
wheelchair seat. (Illustration D)
2. Remove the grommets from
the screws, place screws
through the grommets at
the ends of both belt
sections, and refasten the
screws to the wheelchair seat.
(Illustration E)
3. Select either hole in
belt depending upon desired
length, closer holes will yield
a shorter length,
holes closet to the end
will yield a longer length.
4. Attach the two “spade”
connectors on the connector
wire to those on the seat belt.
(Illustration F)
Note, that for removable arm
wheelchairs it may be easier
to install the belt after the arm
is removed.
5. Place connector cord through the space between
the wheelchair seat and backrest. Make certain that
it is away from wheels and other moving parts.
WHEELCHAIR BELT INSTALLATION (Loop)
1. UnThread the loop end of the belt.
2. Remove the arm of the wheelchair
(if removable arm)
3. Lay belt on
wheelchair while
holding loop end,
place loop end around
the bottom of the
wheelchair (Fig. 1).
4. Place loop and
webbing under both
rectangular rings (Fig. 2)
See Reverse Side
for Loop
installation 5-6.
Cord Loop
Re-Order # Description
Belt Length Unit
909371
E-Z Release Belt with Grommets
30”-44”
Set
914119
E-Z Release Belt with Loops
30”-44”
Set
E-Z Release Belt Alarm
Safety Alarm
