SKF CMSS 785 Series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 52

SKF CMSS 785 Series Скачать руководство пользователя страница 48

Appendix C – Cable wiring/laying recommendations

The following recommendations are typically made to avoid issues arising from cable laying and installation.
•  Pulsed signals (phase marker, rotation) are preferably to be on a separate cable from vibration and similar signals.
•  Do not mix signal transmission cables and control/power system cables.
•  All cable installations are to be made using grounded conduit pipe or cable racks.

Good example

Transmission cable
3-wire shielded cable

Power line or
control line

Conduit pipe

(Power line)

(Signal line)

Conduit pipe

Conduit pipe

Signal transmission cable
3-wire shielded cable

Power line or
control line

(Signal line)

(Power line)

Pulse /High amplitude vibration
signal transmission cable

Cable rack
(conduit pipe)

Cable wiring/laying example:

Bad example

(Signal system/Power system combined)

Signal transmission cable
3-wire shielded cable

Power line or
control line

Conduit pipe

Power line or
control line

Pulse signal line

(Signal system/Power system
combined)

Cable rack
(conduit pipe)

3

9

48

48

«
...
46
47
48
49
50
...
»

Содержание CMSS 785 Series





















































Отзывы:

Нет отзывов