manualshive.com logo in svg

SKC QuickTake 30, Руководство по эксплуатации

Поделиться
Скачать
SKC QuickTake 30 Скачать руководство пользователя страница 10

9

Operating from AC Power

The QuickTake 30 may be run using AC power with the ba

tt

 ery and AC 

charger/adapter. Insert the charger plug into the jack on the pump and the 
charger into a standard wall outlet. Operate the pump. 

Cautions, Warnings, and Notes

•  The charge light on the LED will 

fl

 ash if the ba

tt

 ery is charging during AC 

operation.

•  The AC charger/adapter can be used to extend ba

tt

 ery run time, but it 

is not a ba

tt

 ery eliminator. Therefore, it will not provide inde

fi

 nite run 

times.

•  Do not operate or charge the pump in hazardous locations.

•  Use only the SKC-approved ba

tt

 ery and charger for this pump. Use of an 

unapproved ba

tt

 ery and/or charger may damage the ba

tt

 ery and the pump 

and voids any warranty.

•  To reduce risk of injury, 

fi

 re, or electric shock, always follow basic safety 

precautions when using this product.

•  Do not submerge the pump or subject it to any liquids.

•  Protect the sample pump from weather when in use outdoors.

•  Tampering with the ba

tt

 ery pack or using a repaired or rebuilt ba

tt

 ery 

pack voids any warranty and UL Listing for intrinsic safety.

•  Do not open, disassemble, short circuit, crush, incinerate, or expose the 

ba

tt

 ery to 

fi

 re or high temperatures.

•  Failure to follow warnings or cautions voids any warranty.

Содержание QuickTake 30


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды