background image

Form 38054 Rev 1902

Page 31 of 32

www.skcinc.com

Accessories/Replacement Parts

Accessories 

Cat. No.

Standard Charging Cradle, 

requires power supply, see below

220-800

Enhanced Charging Cradle (e-Cradle), 

includes USB cable and DataTrac Pro Software, 

requires power supply, see below

220-900

Single Cradle Power Supply, 

for use with one charging cradle, 100-240 V

220-600

Multi Cradle Power Supply,

 for use with 2 to 5 charging cradles, 100-240 V

220-700

DataTrac Pro Hardware Accessory Kit,

 includes e-Cradle, single power supply, and 

USB 2.0A to mini-B cable. DataTrac Pro Software is available for download.

 

AirChek TOUCH Pump and DataTrac Pro Software are required.

877-93

Low Flow (5 to 500 ml/min) Kit

 includes All-in-One adjustable tube holder and Type A protective tube cover

210-500

Protective Pouch,

 nylon, with adjustable waist belt and shoulder strap, black

224-911

chek-mate Calibrator with CalChek,

 0.50 to 5 L/min, includes 9-volt alkaline battery, 

CalChek automatic calibration, and NIST-traceable calibration certi

fi

 cate

375-0550N

CalChek Communication Cable,

 

required for CalChek calibration

375-200

Pulsation Dampener,

 

required for CalChek Full Calibration

375-100

Replacement Parts 

Cat. No.

Replacement Battery Pack,

 Li-Ion*

P75718

Belt Clip

P51824

Inlet

P20423

Inlet Filter/O-rings, 

pk/3

P4001

Screen Cover

P20422

* Li-Ion Battery Testing and Shipment

Rechargeable lithium-ion batteries for use with SKC sample pumps have been tested in accordance with the UN Manual and are proven to meet requirements of each test in the 

UN 

Manual of Tests and Criteria,

 Part III, subsection 38.3. The batteries are rated below 100 watt-hours (Wh).

AirChek TOUCH pumps contain Li-Ion batteries and are subject to special shipping regulations. Consult with your carrier for more information on Lithium Battery Shipping Regulations 
UN 3480 and UN 3481 or visit SKC’s website for more information at www.skcinc.com/catalog/pdf/instructions/1921.pdf

  Use only SKC-approved parts to ensure reliable performance and to maintain the UL Listing for intrinsic safety. Failure to do so 

voids any warranty.

  Use of a repaired or rebuilt battery pack VOIDS ANY WARRANTY.

SKC Limited Warranty and Return Policy

SKC products are subject to the SKC Limited Warranty and Return Policy, which provides SKC’s sole liability and the buyer’s exclusive 
remedy. To view the complete SKC Limited Warranty and Return Policy, go to h

tt

 p://www.skcinc.com/warranty.

Содержание 220 Series

































Отзывы: