Sitron SLU Скачать руководство пользователя страница 4

Fig. 2: Level meter dead zone

m – Dead zone 
(blind zone, blocking distance) 

-

Fig. 3: Installation distance from the tank wall

SLU–02 ; 10

d > 1/12 c  
(min. 200 mm)

SLU–06

d > 1/8 c 
(min. 200 mm)

SLU–20

d > 1/10 c
(min. 200 mm)

Fig. 4: Possible installation of the installation neck

a  –  Neck height
b  –  Neck width
m – Dead zone (blind zone, blocking dist.)

SLU–02 ; 06

a < 3 b
b > 100 mm

SLU–10

a < 1.5 b
b > 100 mm 

SLU–20

a < 1.5 b
b > 150 mm

d – Distance from
      the tank wall 

c – Maximum reach  
     of the level meter

4

Installation Instructions

Install the level meter in the vertical position into the upper lid of the tank or vessel or 
reservoir using a the threaded connection, a fastening nut or a flange so that the level 
meter axis is perpendicular to the surface level of the measured liquid( Fig.1)

The min. dimensional parameters to install the level meter in to a lid or a celling of tank are 
givening (Fig.3)

When installing in an open channel (reservoir, drain etc.) install the level meter on to a 
bracket as close as possible to the expected max. level.

Each measuring range of SLU models has a specified ‘‘dead zone’.   This means that 
within the first 10 to 50 centimers (depending on the model) below the transmitter, no 
signal reflected in this area can be evaluated. The dead zone (Fig.2) determines the min. 
distance  possible  between  the  level  meter  and  the  highest  surface  level.  The  min. 
distances to the medium are given in the chapter ‘Specifications’.

It is necessary to install the level meter so that the target level will not interfere with the 
dead zone when filled up to the maximum level. If the measured level interferes with the 
dead zone, the level meter will not work supply the correct output signal.

Fig.1 Recomended installation
         in the tank

d – Distance from
      the tank wall 

c – Maximum reach  
     of the level meter

If the maximum surface level in the tank interferes with the dead zone, the level mater has to be mounted higher within a 
neck extention to the tank.  In this way, the tank can be filled to the maximum volume. The inner neck surface has to be 
even and smooth (without edges and welded points) the inner edge should be rounded where the ultrasonic wave 
eminates from the pipe. The neck diameter should be as large as possible but the neck height should be as low as 
possible,  minimizing  the  extra  distance  between  the  medium  and  the  sensor.    Recommended  dimensions  of  the 
extended neck are given in (Fig.4).

Installation Manual

Содержание SLU

























Отзывы: