Sitecom 450N Скачать руководство пользователя

Страница: 29 / 84

E |3

Advanced Settings

This tab allows you to set the advanced wireless options. The options included

are Authentication Type, Fragment Threshold, RTS Threshold, Beacon

Interval, and Preamble Type. You should not change these parameters unless

you know what effect the changes will have on the router.

Authentication Type

There are two authentication types: "Open System"

and "Shared Key". When you select "Open System", wireless stations can

associate with this wireless router without WEP encryption. When you select

"Shared Key", you should also setup a WEP key in the "Encryption" page.

After this has been done, make sure the wireless clients that you want to

connect to the device are also setup with the same encryption key.

Fragment Threshold

"Fragment Threshold" specifies the maximum size of a

packet during the fragmentation of data to be transmitted. If you set this

value too low, it will result in bad performance.

RTS Threshold

When the packet size is smaller then the RTS threshold, the

wireless router will not use the RTS/CTS mechanism to send this packet.

Beacon Interval

is the interval of time that this wireless router broadcasts a

beacon. A Beacon is used to synchronize the wireless network.

Содержание 450N





















































































Результаты поиска

Содержание 450N

Отзывы:

Похожие инструкции для 450N

Бренды по названию

Популярные бренды

Sitecom 450N, Руководство пользователя

Результаты поиска

Содержание 450N

Отзывы:

Похожие инструкции для 450N

Бренды по названию

Популярные бренды