5
cut or snagged and your hand or arm may be
pulled into the spinning accessory.
13.
Never lay the power tool down until the
accessory has come to a complete stop.
The
spinning accessory may grab the surface and pull
the power tool out of your control.
14.
Do not run the power tool while carrying it at
your side.
Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
15.
Regularly clean the power tool’s air vents.
The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
16.
Do not operate the power tool near flammable
materials.
Sparks could ignite these materials.
17.
Do not use accessories that require liquid
coolants.
Using water or other liquid coolants
may result in electrocution or shock.
18.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be
forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
a)
Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The
operator can control torque reactions or kickback
forces, if proper precautions are taken.
b)
Never place your hand near the rotating
accessory.
Accessory may kickback over your
hand.
c)
Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to
the wheel’s movement at the point of snagging.
d)
Use special care when working corners,
sharp edges etc. Avoid bouncing and snagging
the accessory.
Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e)
Do not attach a saw chain woodcarving blade
or toothed saw blade.
Such blades create
frequent kickback and loss of control
19.
Safety Warnings Specific for Grinding and
Abrasive Cutting-Off Operations:
a)
Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel.
Wheels for
which the power tool was not designed cannot be
adequately guarded and are unsafe.
b)
The guard must be securely attached to the
power tool and positioned for maximum safety,
so the least amount of wheel is exposed
towards the operator.
The guard helps to protect
operator from broken wheel fragments and
accidental contact with wheel.
c)
Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel.
Abrasive cut-off wheels
are intended for peripheral grinding, side forces
applied to these wheels may cause them to
shatter.
d)
Always use undamaged wheel flanges that
are of correct size and shape for your selected
wheel.
Proper wheel flanges support the wheel
thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel flanges.
e)
Do not use worn down wheels from larger
power tools.
Wheel intended for larger power tool
is not suitable for the higher speed of a smaller tool
and may burst.
20.
Additional Safety Warnings Specific for
Abrasive Cutting-Off Operations:
a)
Do not “jam” the cut-off wheel or apply
excessive pressure. Do not attempt to make an
excessive depth of cut.
Overstressing the wheel
increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility
of kickback or wheel breakage.
b)
Do not position your body in line with and
behind the rotating wheel.
When the wheel, at
the point of operation, is moving away from your
body, the possible kickback may propel the
spinning wheel and the power tool directly at you.
c)
When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback may
