background image

22 

Problems

Cause

Rimedies

The machine does not start 

The circuit breaker is set at “0" 

Set the switch to "I" 

The plug switch is set at "0" 

Set the switch to "I" 

The start button does not work 

Contact Technical  
Support 

The safety devices are 
removed or not present. 

Check safety devices 

The rotator rotates in the 
opposite direction from that 
indicated on the arrow (on three-
phase mod.)  

Reverse phase wire on plug 

Contact Technical  
Support 

The product does not grind 
correctly  

Plate and knife do not close 
properly 

Properly tighten the plate and 
the knife 

Presence of scoring on the plate 

or knife not perfectly fitting (on 

the plate surface) 

Replace the defective torque plate 
and knife 

Loose ring nut 

Tighten the ring nut properly 

7.2 - Cleaning the Machine 

WARNING! 

Unplug the machine from the mains before cleaning. Do not clean the machine 

with a water jet. Use only non-toxic cleaners, and specifically for the cleaning of components 
for use with food. Plates and knives are made of AISI 430 steel, if left wet or to soak, they can 
rust. It is advisable to dry them after washing. 

7.3  WEEE Waste Electrical and Electronic Equipment

  

Pursuant to Article 13 of Legislative Decree 25 July 2005, No.151 
"Implementation of Directive 2002/95/EC, 2002/96/EC and 2003/108/EC on the reduction 
of use of Hazardous Substances in electrical and electronic equipment, and disposal of 
waste

 

  

The symbol of the barred trashbin as shown on the equipment or on its  packaging 
indicates that the product at the end of its life must be separated from other waste.    
The recycling of this equipment at the end of its life is organised and  

managed by the manufacturer. The user who wishes to dispose of this equipment shall contact 
the manufacturer and follow the system that has been adopted to allow the separate collection 
at the end of its life.   
Proper differentiated collection by subsequent sending of the equipment waste to recycling, 
treatment and environmentally compatible disposal helps to avoid  possible negative 
environmental and health effects and promotes the reuse and/ or recycling of materials making 
up the product.   

Illegal disposal of the product by the owner will lead to the application of administrative 
sanctions provided by law.  

8 - Troubleshooting

 

8.1 - Causes of problems and remedies

 

Содержание TC 22























Отзывы: