22
PARTS LIST
69
Clip 8mm
PW01-00022
103
Exhaust Pipe
PW01-00085
70
Fuel Filter
PW01-00056
104
Washer M6
PW01-00086
71
Threaded Bolt
PW01-00057
105
Spring Washer M6
PW01-00087
72
Filter
PW01-00058
106
Hex Bolt M6x25
PW01-00088
73
Filter Foam
PW01-00059
107
Washer M6
PW01-00086
74
Square Clip Nut
PW01-00060
108
Spring Washer M6
PW01-00087
75
Self Tapping Screw 4.8x16
PW01-00061
109
Hex Bolt M6x25
PW01-00088
76
Fuel Valve
PW01-00062
110
Square Clip Nut
PW01-00060
77
Fuel Valve Knob
PW01-00063
111
Plastic Case Right
PW01-00089
78
Washer M4
PW01-00064
112
Flange Bolt M5
PW01-00077
79
Cross Head Screw M4x16
PW01-00065
113
Maintenance Cover Top
PW01-00090
80
Recoil Cover Frame
PW01-00066
114
Cross Head Screw M5x12
PW01-00018
81
Clip 10mm
PW01-00048
115
Control Panel
PW01-00091
82
Air Tube
PW01-00067
116
Self Tapping Screw 4x12
PW01-00079
83
Clip 11mm
PW01-00050
117
Ground Block
PW01-00092
84
Exhaust Tube
PW01-00068
118
Flange Bolt M5x16
PW01-00013
85
Carburettor Gasket Small
PW01-00069
119
Self Tapping Screw 4.2x13 PW01-00093
86
Cross Head Screw M3x8
PW01-00070
120
Self Tapping Screw 4.2x13 PW01-00093
87
Step Mortor
PW01-00071
121
Muffler Shield Right
PW01-00094
88
Cross Head Screw M4x12
PW01-00072
122
Clamp Spring
PW01-00095
89
Step Motor Support
PW01-00073
123
Muffler
PW01-00096
90
Choke Block
PW01-00074
124
Case Vent
PW01-00097
91
Block Spring
PW01-00075
125
Cross Head Screw M5x12
PW01-00018
92
Clip 9mm
PW01-00020
126
Fan Shield
PW01-00098
93
Air Tube
PW01-00076
127
Flange Bolt M5x16
PW01-00013
94
Clip 10mm
PW01-00048
128
Fan
PW01-00099
95
Flange Bolt M5
PW01-00077
129
Flange Bolt M10x1
PW01-00100
96
Air Filter Cover
PW01-00078
130
Fan Hood
PW01-00101
97
Self Tapping Screw M4x12
PW01-00079
131
Self Tapping Screw 3.5x12 PW01-00102
98
Plastic Case Left
PW01-00080
132
Flange Bolt M5x16
PW01-00013
99
Cross Head Screw M5x20
PW01-00081
133
Muffler Shield Left
PW01-00103
100
Maintenance Cover Left
PW01-00082
134
Washer M4
PW01-00064
101
Cross Head Screw M6x16
PW01-00083
135
Self Tapping Screw 4x16
PW01-00104
100
Maintenance Cover Left
PW01-00082
135
Self Tapping Screw 4x16
PW01-00104
101
Cross Head Screw M6x16
PW01-00083
11
OPERATING INSTRUCTIONS
Hot Surfaces:
Always ensure that the generator is turned off and allowed
to fully cool before any refuelling or maintenance procedures are car-
ried out.
Ensure that the generator is on a flat level surface.
•
Remove the maintenance panel A.
•
Ensure that the generator is on a flat level surface.
•
Remove the filler cap / Dipstick by turning it anti-clockwise.
•
Slowly pour the oil into the crankcase using the supplied oil filler bottle.
•
Check the oil level by pushing the filler cap back into its hole up to the bottom
of the threads (do not screw the cap in).
•
Once the oil level is between the upper and the lower marks on the oil gauge
(see below), replace it and turn clockwise to fully tighten.
The oil level should be checked every 8 hours or daily.
The oil should be changed after the first 8 hours of operation; thereafter change the oil
after 30 hours of operation or less if the generator is operated under constant heavy
loads or in high ambient temperatures.
Oil Filler Cap / Dipstick
Upper Level
Lower Level
Filling the crankcase with oil / Checking the oil level:
Caution:
The generator is drained of oil and fuel at the factory prior to
shipping. SAE W15-30 oil or equivalent is recommended for these gen-
erators.