22
OPERATING INSTRUCTIONS….cont
Once fully assembled and adjusted, and all safety precautions have been followed;
the pillar drill is ready to be run.
Your SIP pillar drill is fitted with a safety NVR (No Volt Release) switch. This means that if
the power is cut to the drill (such as in a power failure); the motor will not start to run
once the power is returned without the operator following the instructions below to re-
start the drill.
To start the drill - press the green (I) button.
To stop the drill - press the red (0) button or press down on the emergency stop cover.
ON / OFF (NVR) SWITCH
ADJUSTING THE SPEED - 01700 & 01701
Open the pulley cover.
Slacken off the belt tension lock.
Consult the chart inside the pulley cover, and position the belt on the pulley's ac-
cording to the spindle speed required.
When the belt has been correctly positioned, re-tension by levering the motor
away from the head (024); Lever the motor with its bracket, away from the head,
so that tension is applied to the belt.
Tension is correct when the belt deflects by approx. ½” at its centre, when using
reasonable thumb pressure.
Lock the motor in this position using the belt tension lock.
Note:
The speed of the pillar drill can be changed by adjusting the position
of the belt on the pulley system. See the chart inside the pulley cover for
speed configurations.
Danger:
Before making any changes or adjustments, ensure that the drill is
turned off, and the mains lead is removed from the supply socket.
Belt Tension Lock
024
39
PARTS LIST - 01703
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
1.
Base
WD01-00863
35.
Motor plate
WD01-00874
2.
Column flange
WD01-00864
36.
Spring washer M12
WD01-00676
3.
Spring washer M10
WD01-00795
37.
Nut M12
WD01-00821
4.
Bolt (M10 x 25)
WD01-00796
38.
Grub screw (M8 x10)
WD01-00689
5.
Rack
WD01-00908
39.
Motor pulley
WD01-00876
6.
Column
WD01-00865
40.
Motor
WD01-00877
7.
Grub screw (M6 x 12)
WD01-00740
41.
Nut M8
WD01-00687
8.
Rack collar
WD01-00799
42.
Cam assembly
WD01-00909
9.
Screw (M6 x 16)
WD01-00708
43.
Washer
WD01-00878
10.
Handle cap
WD01-00800
44.
Protecting ring
WD01-00839
11.
Screw (M8 x 20)
WD01-00801
45.
Speed label
WD01-00879
12.
Spring washer M8
WD01-00673
46.
Pulley cover
WD01-00880
13.
Handle knob
WD01-00802
47.
Microswitch
WD01-00706
14.
Handle
WD01-00803
48.
Washer M5
WD01-00881
15.
Label
WD01-00893
49.
Spring washer M5
WD01-00882
16.
Knob
WD01-00867
50.
Nut M5
WD01-00697
17.
Scale
WD01-00805
51.
Nut M6
WD01-00710
18.
Connection
WD01-00806
52.
Spring washer M6
WD01-00707
19.
Pinion shaft
WD01-00809
53.
Washer M6
WD01-00702
20.
Roll pin (5 x 16)
WD01-00868
54.
Microswitch holder
WD01-00709
21.
Warning label
WD01-00685
55.
Eccentric shaft
WD01-00883
22.
Screw (M5 x 10)
WD01-00726
56.
Centre pulley
WD01-00884
24.
Roll pin (5 x 25)
WD01-00869
57.
Bearing 6202
WD01-00771
25.
Roll pin (6 x 18)
WD01-00760
58.
Circlip
WD01-00831
26.
Locking handle
WD01-00870
59.
Belt O-565
WD01-00833
27.
Belt tension handle
WD01-00812
60.
Knurled screw
WD01-00885
28.
Circlip
WD01-00813
61.
Circlip
WD01-00704
29.
Circlip
WD01-00871
63.
Screw (M5 x 16)
WD01-00838
30.
Shaft
WD01-00872
64.
Mains lead clamp
WD01-00700
31.
Adjusting shaft
WD01-00873
65.
Protecting ring
WD01-00770
32.
Washer M12
WD01-00819
66.
Belt O-678
WD01-00886
33.
Bolt (M8 x 25)
WD01-00695
67.
Spindle pulley
WD01-00887
34.
Washer M8
WD01-00672
68.
Circlip
WD01-00713
