48
PARTS LIST - 01706
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
1.
Base
WD02-00284
34.
Washer M8
WD01-00672
2.
Column flange
WD02-00285
35.
Motor plate
WD02-00296
3.
Spring washer M10
WD01-00795
36.
Spring washer M12
WD01-00676
4.
Bolt (M10 x 25)
WD01-00796
37.
Nut M12
WD01-00821
5.
Rack
WD02-00286
38.
Grub screw (M8 x10)
WD01-00689
6.
Column
WD02-00287
39.
Motor pulley
WD02-00297
7.
Grub screw (M6 x 12)
WD01-00740
40.
Motor
WD02-00298
8.
Rack collar
WD02-00288
41.
Nut M8
WD01-00687
9.
Screw (M6 x 16)
WD01-00708
42.
Cam assembly
WD02-00299
10.
Handle cap
WD02-00289
43.
Washer
WD02-00300
11.
Screw (M8 x 20)
WD01-00801
44.
Protecting ring
WD01-00839
12.
Spring washer M8
WD01-00673
45.
Speed label
WD02-00301
13.
Handle knob
WD02-00290
46.
Pulley cover
WD02-00302
14.
Handle
WD02-00291
47.
Microswitch
WD01-00706
15.
Label
WD02-00292
48.
Washer M5
WD01-00881
16.
Knob
WD01-00867
49.
Spring washer M5
WD01-00882
17.
Scale
WD02-00293
50.
Nut M5
WD01-00697
18.
Connection
WD02-00294
51.
Nut M6
WD01-00710
19.
Pinion shaft
WD02-00295
52.
Spring washer M6
WD01-00707
20.
Roll pin (5 x 16)
WD01-00868
53.
Washer M6
WD01-00702
21.
Warning label
WD01-00685
54.
Microswitch holder
WD01-00709
22.
Screw (M5 x 10)
WD01-00726
55.
Eccentric shaft
WD02-00303
23.
Spindle pulley nut (M24 x 1.5) WD01-00907
56.
Centre pulley
WD02-00304
24.
Roll pin (5 x 25)
WD01-00869
57.
Bearing 6202
WD01-00771
25.
Roll pin (6 x 18)
WD01-00760
58.
Circlip
WD01-00831
26.
Locking handle
WD01-00870
59.
Belt A550
WD02-00305
27.
Belt tension handle
WD01-00812
60.
Knurled screw
WD02-00306
28.
Circlip
WD01-00813
61.
Circlip
WD01-00704
29.
Circlip
WD01-00871
63.
Screw (M5 x 16)
WD01-00838
30.
Shaft
WD01-00872
64.
Mains lead clamp
WD01-00700
31.
Adjusting shaft
WD01-00873
65.
Protecting ring
WD01-00770
32.
Washer M12
WD01-00819
66.
Belt A620
WD02-00307
33.
Bolt (M8 x 25)
WD01-00695
67.
Spindle pulley
WD02-00308
13
Guarantee:
These SIP pillar drills are covered by a 12 month parts and labour warranty covering
failure due to manufacturers defects. This does not cover failure due to misuse or op-
erating the pillar drill outside the scope of this manual - any claims deemed to be out-
side the scope of the warranty may be subject to charges Including, but not limited to
parts, labour and carriage costs.
This guarantee does not cover consumables such as the chuck, belts etc.
In the unlikely event of warranty claims, contact your distributor as soon as possible.
Note:
Always make sure the mains supply is of the correct voltage and the
correct fuse protection is used. In the event of replacing the fuse always
replace the fuse with the same value as the original.
Note:
If an extension lead is required in order to reach the mains supply;
ensure that this too is rated for the correct voltage and fuse rating.
Note:
The cross section of the extension lead should be checked so that it
is of sufficient size so as to reduce the chances of voltage drops.
ELECTRICAL CONNECTION….cont
GUARANTEE
Note:
Proof of purchase will be required before any warranty can be hon-
oured.
