background image

6 | 

P a g e

 

 

PLUMBING INSTALLATION

 

 
CAUTION: Breaker must remain off until installation is complete. 
 
Step 1: Flush cold water line to clear any debris before connecting to unit. 
Step 2: Install a shut off valve and pre filter (Not Supplied) to prevent any 

particles entering the unit that may clog or damage the internal parts. 
Step 3: Using flexible lines, connect the Cold Water line to the water heater 

inlet  labeled  as “cold”.  Connect  furnished  Water  Valve to the water heater 

outlet labeled as “hot”. Connect the HOT WATER outlet line to the Water Valve.  
Step 4: Verify all fittings are tight and secure. Open hot water  source  and 

allow water to run though the water heater for at least 1 to 2 minutes. This 

will purge the air from the water lines and must be performed prior to turning 

on the power at the unit. This is a Mandatory step to prevent Damage to 

Heating Elements.  
DO NOT solder any fittings to unit. This will damage internal sensors and 

components and void the warranty. Use flexible lines and screw fittings only 

to unit.  
A TP valve is not required in most jurisdictions. Verify your local codes 

accordingly and if required install on outlet side only. 
Verify all connections are free of leaks. 
 

Model 

Minimum Flow  Maximum Flow 

 

Connection 

 

SIO 14 

.50 GPM 

4.0 GPM

 

3/4" NPT

 

SIO 18 

.50 GPM 

4.4 GPM

 

3/4" NPT

 

 

 
 
 

Содержание SIO 14























Отзывы: