SINGFLO 2440 Series Скачать руководство пользователя страница 18

 

WARRANTY

LIMITED WARRANTY PROCEDURE

SINGFLO

  warrants  its  pump  to  be  free  of  defects  in  material  and  workmanship  to  the  original  retail 

purchaser  for  the  period  of  one  year beginning with  the  purchase date  of  the unit  or, in  the  absence  of 

proof  of  purchase  date,  one  year  from  the  date  of  manufacture  as  shown  on  the  pump,  not  to  exceed 

two  (2)  years  in  any  event.  Each  pump  has  been  operated  and  tested  before  being  shipped  from 

SINGFLO

's factory. During the warranty period if the pump is not operating correctly, you may return it 

freight pre-paid to your local distributor, dealer or directly to 

SINGFLO

.  

Upon 

SINGFLO

's  inspection,  any  unit  found  faulty  due  to  manufacturing  defects  will  be  repaired  or 

replaced  at  no  charge.  This warranty  does  not  apply  to  any  damage  resulting  from  misuse,  negligence, 

accidents,  improper  installation  or  wiring.  Abuses  such  as  removal  of  the 

SINGFLO

  label,  improper 

repair,  installation,  application,  or  damaged  lower  housing  assembly  due  to  running  dry,  are  also  not 

considered warrant able.  There will be charges applied for any of   the above mentioned non-warrantable 

items. 

If  you  send  the  pump  to  us  for  prompt  repair,  please  package  it  carefully  to  avoid  shipping  damage. 

Enclose  your  name,  address,  a  phone  number  where  you  may  be  reached  and  your  proof  of  purchase 

date. 

The  above  represents  our  warranty  policy.  Under  no  circumstances  will  we  assume  or  accept 

responsibility for unauthorized expenditures, losses, or any costs greater than the basic pump value. 

 

 

 

 

Содержание 2440 Series



















Отзывы: