Singer S0705 Скачать руководство пользователя страница 37

Страница: 37 / 44

MACHINE MAINTENANCE – 37

MACHINE MAINTENANCE

Cleaning the Upper Cutter Area

Turn off the main power switch and unplug the machine.

Cleaning the Feed Teeth

Open the front cover.
With a forward brushing movement, use the lint brush to re-

move any lint.

Note: You may use a vacuum cleaner to clean the upper knife

area or feed teeth.

Turn off the main power switch and unplug the machine.

Deactivate the stitch finger by setting it in “R” position (A).

Open the side and front covers.

Remove the needle(s) and the presser foot.
Remove the set screw (B) with the large screw driver. Re

move the needle plate.
Use the lint brush to remove any lint from around the feed

teeth (C).

Place the stitch plate over the feed teeth, making sure the tab

of the stitch plate (D) is inserted under the edge of the cov

er (E). The hole in the stitch plate (F) should align with the

knob on the machine (G).

Replace and tighten the set screw.

Attach the needle(s) and the presser foot.

Close the side and front covers.

An overlock requires more frequent maintenance than a conventional sewing machine for two reasons:

• A lot of lint is produced when the cutters are cutting the fabric.
•

An overlock runs at a very high speed and needs to be oiled frequently to lubricate the internal working parts.

Storage

When the machine is not in use, be sure to keep it unplugged. Store the machine, so it is not exposed to direct sunlight or hu

midity.

Servicing

If you have any questions regarding service and/or operation, contact our Customer Care department.

Содержание S0705












































Результаты поиска

Содержание S0705

Отзывы:

Бренды по названию

Популярные бренды

Singer S0705, Инструкция по эксплуатации

Результаты поиска

Содержание S0705

Отзывы:

Бренды по названию

Популярные бренды