manualshive.com logo in svg

Singer S0705, Инструкция по эксплуатации

Поделиться
Скачать
Singer S0705 Скачать руководство пользователя страница 25

A

B

C

A

GETTING READY TO SEW – 

25

Differential Feed Adjustment

The differential feed system consists of two sets of feed 

teeth arranged one behind the other. Both feed teeth work in-

dependently of each other to give perfect results when sew-

ing on speciality fabrics. When the amount of feed by the 

front feed teeth is changed in relation to the feed by the rear 

feed teeth it will “stretch” or “gather” the fabric.
Use the differential feed to prevent stretching of knit fabrics 

and puckering of lightweight fabrics.
For overlock stitching on normal fabric, set the differen-

tial feed adjusting dial (A) to 1.0. The differential feed dial 

clicks when you turn the dial at 1.0.

If the sewn fabric stretches (B), turn the dial counterclock

-

wise (toward 2.0).
If the sewn fabric is gathered (C), turn the dial clockwise 

(toward 0.5).

Presser Foot Pressure Adjustment

The presser foot pressure for sewing based on normal condi-

tions should be set to “N” (A). Adjustments in some instanc

-

es may be necessary. Increase or decrease the pressure until 

you are satisfied with the result. Always test sew on a sample 

of your fabric before sewing on your garment.
Decrease the pressure by turning the adjustment dial towards 

you.
Increase the pressure by turning the adjustment dial away 

from you.
Back to standard setting: Turn the adjustment dial until the 

mark is set to ”N”.

Содержание S0705













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды