Sinexcel PWS1-500KTL-NA Скачать руководство пользователя страница 23

Страница: 23 / 49

Chapter IV Device Installation 15

Fig. 4-2 Installation space of storage inverter

4.4.5

Other requirements

Waterproofing

The protection grade of the cabinet of the storage inverter is IP20. It is only installed and used in a dry and clean room. Water

leakage in room should be avoided so as to prevent the storage inverter from being damaged.

Rat-proofing

After wiring, fireproofing mud should be used to seal inlet and outlet holes so as to meet the rat-proofing requirement.

Cabinet installation

After the cabinet is removed to the installation position of energy storing deice with a forklift or a tool. Fine adjust the cabinet

and remove it to the designed position, open the internal door of cabinet, use M13 screw to fix the cabinet, as shown in Fig.4-

Fig.4-3. Diagram for cabinet base

When the cabinet needs to be fixed on the steel channel, Φ14 holes can be made in the steel channel. Fix the cabinet to the

steel channel with screws, as shown in Fig.4-4.

Fig. 4-4 Fix the cabinet to the steel channel Fig.4-5 Fix the cabinet to the concrete floor

cable
groove

Ground

Foot screw

Cable
groove

Fixed screw

Channel

steel

Содержание PWS1-500KTL-NA


















































Результаты поиска

Содержание PWS1-500KTL-NA

Отзывы:

Похожие инструкции для PWS1-500KTL-NA

Бренды по названию

Популярные бренды

Sinexcel PWS1-500KTL-NA, Руководство пользователя

Результаты поиска

Содержание PWS1-500KTL-NA

Отзывы:

Похожие инструкции для PWS1-500KTL-NA

Бренды по названию

Популярные бренды