Sinclair SWC-04 Скачать руководство пользователя

Страница: 29 / 36

Table 4 Meaning of Each Error

Error

Code

Error

Code

Drive board communication error

Compressor overheating protection

Return air temperature sensor open/short

circuited

Indoor and outdoor units unmatched

evaporator temperature sensor open/short

circuited

IPM temperature sensor open/short circuited

Indoor unit liquid valve temperature sensor

open/short circuited

Pump-down

Indoor gas valve temperature sensor open/

short circuited

Defrost or oil return

Outdoor unit condenser mid-tube temperature

sensor open/short circuited

Communication line misconnected or

expansion valve error

Forced defrosting

Indoor and outdoor communication error

Compressor startup failure

DC bus under-voltage protection

High discharge temperature protection

DC bus over-voltage protection

PH Overload protection

Outdoor ambient temperature sensor open/

short circuited

Whole unit over-current protection

Compressor demagnetization protection

HE Over phase current protection

PFC protection

Compressor desynchronizing

IPM Current protection

Over-power protection

IPM Temperature Protection

Discharge temperature sensor open/short

circuited

Capacitor charging error

Compressor phase current sensing circuit

error

Frequency restricted/reduced with whole

unit current protection

Compressor phase lo ss/reversal

protection

High pressure protection

System charge shortage or blockage

protection

Low pressure protection

Frequency restricted/reduced with IPM

current protection

Compressor stalling

Frequency restricted/reduced with high

discharge temperature

Over-speeding

Frequency restricted/reduced with anti-

freezing protection

Drive board temperature sensor error

Indoor unit full water error

AC contactor protection

Anti-freezing protection

Temperature drift protection

AC input voltage abnormal

Sensor connection protection

Whole unit current sensing circuit error

DC bus voltage drop error

4-way valve reversing error

Outdoor fan 1 error protection

Motor stalling

Indoor fan tripping error

Outdoor fan 2 error protection

Frequency restricted/reduced with

overload protection

PG motor zero-crossing protection

Frequency restricted/reduced with IPM

temperature protection

compressor inhalation temperature sensor error

Wired Controller

SWC-04

Содержание SWC-04





































Результаты поиска

Содержание SWC-04

Отзывы:

Похожие инструкции для SWC-04

Бренды по названию

Популярные бренды

Sinclair SWC-04, Руководство пользователя

Результаты поиска

Содержание SWC-04

Отзывы:

Похожие инструкции для SWC-04

Бренды по названию

Популярные бренды