background image

Sinclair alarm interface unit SAI-01 

11 

 

OUTDOR UNIT ERROR 

Listed as ODU ERROR in the table. 

Code  Name 

Note 

E4 

Compressor discharge high-temperature protection 

  

F0 

Lack of refrigerant 

  

F3 

Broken/shorted ambient temperature sensor 

  

F4 

Condenser outlet temperature sensor failure 

  

F5 

Compressor discharge sensor failure 

  

P5 

Compressor overcurrent protection 

  

P8 

Drive unit module high-temperature protection 

  

H3 

Compressor overload or compressor overheating protection     

H5 

IPM protection 

  

L3 

ODU fan DC motor failure 

  

Table 6: ODU errors 

AGGREGATED ERROR 

Listed as ERROR (IDU+ODU) in the table. It includes the summary of the above errors of indoor unit, 
outdoor unit and communication.  

Code  Name 

Note 

E2 

Indoor unit freezing protection 

Does not appear on 
the IDU display 

E8 

IDU fan overload/failure 

  

F1 

Broken/shorted room temperature sensor 

  

F2 

Broken/shorted IDU evaporator temperature sensor 

  

C5 

Invalid power code 

  

H6 

Fan DC motor malfunction 

  

JF 

Wi-Fi module malfunction 

  

E4 

Compressor discharge high-temperature protection 

  

F0 

Lack of refrigerant 

  

F3 

Broken/shorted ambient temperature sensor 

  

F4 

Condenser outlet temperature sensor failure 

  

F5 

Compressor discharge sensor failure 

  

P5 

Compressor overcurrent protection 

  

P8 

Drive unit module high-temperature protection 

  

H3 

Compressor overload or compressor overheating protection  

  

H5 

IPM protection 

  

L3 

ODU fan DC motor failure 

  

E6 

Communication error 

  

Table 7: Aggregated ERROR (IDU+ODU) 

 

 

Содержание SAI-01

















Отзывы: