Sinclair MV-F09BI Скачать руководство пользователя страница 8

Страница: 8 / 38

● After selecting auto mode, air conditioner will operate automatically according to

ambient temperature. Set temperature can’t be adjusted and will not be displayed

as well. Press "

AN" button can adjust fan speed. Press " " button can adjust

fan blowing angle.

●

After selecting cool mode, air conditi

ner will operate under cool mode. Press "+"

or "-" button to adjust set temperature. Press "FN" button to adjust fan speed.

Press " " button to adjust fan blowing angle.

● When selecting dry mode, the air conditioner operates at low speed under dry

mode. Under dry mode, fan speed can’t be adjusted. Press " " button to adjust

fan blowing angle.

● When selecting fan mode, the air conditioner will only blow fan, no cooling and

no heating.

All indicators are OF

. Operation indicator is ON. Press "

AN" button

to adjust fan speed. Press

● When selecting heating mode, the air conditioner operates under heat mode.

Press "+" or "-" button to adjust set temperature. Press "FAN" bu

tton to

adjust

fan

speed. Press " " bu

tton to

adjust fan blowing angle. (Cooling only unit

won’t

receive heating mode signal. If setting heat mode with remote controlle

, press

ON/OFF button can’t start up the unit).

Note:

● For preventing cold ai

, after starting up heating mode, indoor unit will delay 1~5

minutes to blow air (actual delay time is depend on indoor ambient temperature).

● Set temperature range from remote controller: 16~30

℃

; Fan speed: auto, low

speed, medium speed, high speed.

Note:

●

After putting through the powe

, the air conditioner will give out a sound.

After that, you can operate the air conditioner by using remote control

ler

ON/OFF button

MODE button

Press this button can turn on or turn off the air conditione

After turning on the air

conditione

, operation indicator " "on indoor uni

’s display is ON (green indica

tor

The colour is different for different models), and indoor unit will give out a sound.

Press this button to select your required operation mode.

O COOL

HEA

" " button to adjust fan blowing angle.

● This is a general use remote controller, it could be used for the air conditioners

with multifunction; For some function, which the model doesn't have, if press

the corresponding button on the remote controller that the unit will keep the

original running status.

3.3 Introduction for buttons on remote controller

Содержание MV-F09BI







































Результаты поиска

Содержание MV-F09BI

Отзывы:

Похожие инструкции для MV-F09BI

Бренды по названию

Популярные бренды

Sinclair MV-F09BI, Руководство пользователя

Результаты поиска

Содержание MV-F09BI

Отзывы:

Похожие инструкции для MV-F09BI

Бренды по названию

Популярные бренды