Sinclair MV-D BI Series Скачать руководство пользователя страница 19

Maintenance notes

Check whether the maintenance area or the room area meet the requirement of the

nameplate.

- It’s only allowed to be operated in the rooms that meet the requirement of the

Check whether the maintenance area is well-ventilated.

- The continuous ventilation status should be kept during the operation process.

Check whether there is fire source or potential fire source in the maintenance area.

- The naked flame is prohibited in the maintenance area; and the “no smoking”

warning board should be hanged.

nameplate.

Check whether the appliance mark is in good condition.

- Replace the vague or damaged warning mark.

/

/

/

/

14.5 16.8 19.3

22

24.8 27.8 31 34.3 37.8 41.5 45.4 49.4 53.6

7 7.9 8.9 10 11.2 12.4 13.6 15 16.3 17.8 19.3

5.2 6.1

1.6 1.9 2.1

2.4

2.8 3.1 3.4 3.8

4.2

6

5.5

5

4.6

1.1 1.3 1.4 1.6 1.8 2.1 2.3 2.6 2.8 3.1 3.4 3.7

4

floor location

wall mounted

window mounted

ceiling mounted

Minimum

room

2

area( m  )

 

12

 

 

 

5

 

Safety operation of flammable refrigerant

 

Qualification requirement for installation and maintenance man

 

 

All the work men who are engaging in the refrigeration system should bear the

 

 

valid certification awarded by the authoritative organization and the qualification

 

 

for dealing with the refrigeration system recognized by this industry. If it needs

 

 

other technician to maintain and repair the appliance, they should be supervised

 

 

by the person who bears the qualification for using the flammable refrigerant.

 

 

It can only be repaired by the method suggested by the equipment’s manufacturer.

 

 

Installation notes

 

 

The air conditioner is not allowed to use in a room that has running fire (such as fire

 

 

source, working coal gas ware, operating heater).

 

 

It is not allowed to drill hole or burn the connection pipe.

 

 

The air conditioner must be installed in a room that is larger than the minimum room

 

 

area. The minimum room area is shown on the nameplate or following table a.

 

 

Leak test is a must after installation.

 

 

table a - Minimum room area ( m  )

2

 

 

Charge amount (kg)

≤1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9

 

2

2.1

 

2.2

2.3

 

2.4

2.5

Содержание MV-D BI Series





















Отзывы: