Sinclair ASCU-12A Скачать руководство пользователя страница 95

Страница: 95 / 202

U-MATCH AIR CONDITIONERS MAINTENANCE

Trouble

Code

Trouble Name

Origin of

Trouble Signal

Control Description

30 minutes, the unit can not be restored itself and the buzzer will

give out an alarm. Push the ON/OFF button to shut off the unit.

And then push ON/OFF button again, if high voltage protection

disappears, operation will restore, or otherwise, the fault is

displayed.

Communications

Failure

Communication

When outdoor unit is energized and fails to receive data of indoor

unit within 30 seconds, an indoor unit communication fault is

reported. The compressor and the outdoor unit will be shut off,

and the four way valve will be stopped 2 minutes after the

compressor outage in heating state.

If indoor unit fails to receive information of outdoor unit, a

communication fault is reported. The indoor unit is shut off and

an indicator is twinkling. If the display board fails to receive

information of outdoor unit, a communication fault is determined

and displayed and the unit does not actuate. After communication

becomes normal, the system can restore to the previous running

state itself.

Indoor Fan

Protection

Indoor unit

If fan overload protection is detected for continuous 3 seconds,

relevant compressor and fan shall be shut off immediately and a

fault code E8 is displayed, and at the same time, the buzzer gives

out an alarm. Push the ON/OFF key, if the fault disappears, clear

the fault display and push the ON/OFF key for restarting the

system.

Full Water

Protection

Liquid level switch

Water full is detected for continuous 8 seconds after the system is

powered on, the water full protection is initiated and the indicator

is twinkling (or E9 is displayed). Under refrigeration and

dehumidification mode, the outdoor fan and the compressor are

shut off and the indoor fan stops after 1 minute delay; under

heating mode, he outdoor fan and the compressor are shut off, the

four way valve keeps at the previous status, and the indoor fan

stops after 1 minute delay; under air supply mode, the load of

indoor unit remains.

Failure of Indoor Room

Sensor at Air Intake

Indoor environment

Thermal bulb

Open-circuit or short-circuit of the indoor environment thermal

bulb is detected for continuous 5 seconds, indoor environment

temperature will be set compulsively at 24 degree, the system

does not take any measure, and only the indicator is twinkling or

fault code F0 is displayed. After the fault is removed, the system

can restore operation by itself. Under air supply mode, only the

Содержание ASCU-12A











































































































































































































Результаты поиска

Содержание ASCU-12A

Отзывы:

Бренды по названию

Популярные бренды

Sinclair ASCU-12A, Руководство по обслуживанию

Результаты поиска

Содержание ASCU-12A

Отзывы:

Бренды по названию

Популярные бренды